Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex D-100 and D-1000 dryer: start-up, heat dial, heater height, belt speed and shutdown
Start the belt before the heat, then run the heat dial on HI for 10 to 15 minutes to warm up. Vastex suggests running on HI and tuning the cure with belt speed and heater height, with the heater about 2 to 3 in above the garment and 20 to 25 seconds in the chamber as a plastisol starting point. Turn the heat off and keep the belt running until the heater is down to 300°F before you stop the conveyor.
The D-100 and D-1000 have two controls: a heat dial marked LO, 2, 3, 4, 5, 6 and HI, and a belt speed knob. The heat dial switches the heater on and off in cycles; the higher the number, the longer it stays on, and HI is full power. A red light shows the heat control is on. Three things decide your cure: heat, heater height and belt speed.
Start-up
-
Plug in
With the breaker and both dryer controls off, plug the dryer into its dedicated outlet and switch the breaker on.
-
Clear the belt
Remove anything on the belt or in the chamber.
-
Belt first
Turn the belt speed knob clockwise to start the belt and set your speed. Counterclockwise slows it; turn it fully counterclockwise until it clicks for off.
-
Then heat
Turn the heat dial to HI and let the dryer warm up for 10 to 15 minutes.
Never stop the belt while the heater is hot. Vastex warns the belt is damaged if it sits still under a heater above 300°F (149°C).
Dial in the cure
-
Heat
Vastex often recommends leaving the dial on HI and adjusting with belt speed and heater height.
-
Heater height
Use the knob on each side of the chamber to raise or lower the heater. Run it about 2 to 3 in above the garment. You can tilt it for uneven items such as hats.
-
Belt speed
For plastisol, start with about 20 to 25 seconds in the chamber. Water-based and discharge inks need longer, often 50 to 90 seconds, with less heat.
-
Measure
Check the ink temperature regularly. With a heat gun, aim at the ink while it is still under the heater, toward the outside edge of the print.
| Ink | Vastex starting point |
|---|---|
| Plastisol | About 20 to 30 seconds in the chamber, ink reaching 320 to 330°F throughout |
| Water-based or discharge | 50 to 90 seconds, lower temperature as time goes up, with a powered exhaust |
Cure times vary with garment moisture and color, ink color and thickness, and shop conditions. Change one thing at a time and wash test.
Shutdown
-
Heat off
Turn the heat dial off and keep the belt running for 10 to 15 minutes while the heater cools.
-
Belt off
Once the heater is at 300°F or lower, turn the belt speed knob to off. You can leave it at your speed setting if the next shift uses the same one.
-
Power off
Switch off the breaker for the dryer and unplug it at the end of each shift.
If the belt won't move or the heater won't heat, see D-100 and D-1000 troubleshooting or Text us a photo or short video at (562) 609-4996.
Watch Vastex's video: Curing plastisol ink with the Vastex D-100
More videos
Embedded from the manufacturer's official channel.
Common questions
Do the numbers on the belt speed dial mean seconds?
No. Vastex says the dial numbers are for reference only. Time a garment through the chamber to know your real dwell time.
What temperature does plastisol need?
Vastex says most plastisol inks must reach 320 to 330°F (160 to 165°C) all the way through. Follow your ink maker's number.
How long does water-based ink take?
Vastex has seen 50 to 90 seconds for a full cure. As you add time, lower the temperature so the garment doesn't scorch. A powered exhaust is recommended.
Can I cure DTF transfers or DTG prints in a D-100?
Vastex doesn't publish settings for those. Ask us and we'll help you test, and follow your film, powder or ink maker's cure temperature.
The dryer is idle between jobs. Should I leave it on HI?
If nothing goes through for more than 10 minutes, Vastex suggests turning the heat to 4 or lower. It takes about 10 minutes to come back up.
- Vastex D-100 and D-1000 assembly and operating instructions, doc 01-23-001E
- Vastex D1-Series and LittleRed specification sheet
- Vastex D100 product page
- AA support requests about conveyor dryers, 2024 to 2026










































































