Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex D-100 or D-1000 belt drifting, belt not moving or no heat: tracking, chain and fuse checks
If the belt drifts, raise or lower the belt aligner a quarter turn at a time: raising one side moves the belt the other way. If the belt won't move, check the 1 amp AGC fuse on the control plate (one on 120 V models, two on 240 V). Chain slack should total 0.25 to 0.38 in. No heat with a working belt points to the heat control or heater, which Vastex replaces, so contact us.
Match your symptom
| What you see | Likely cause | Go to |
|---|---|---|
| Nothing works at all | Dryer unplugged or a building wiring fault | Step 1 |
| Belt drifts to one side or rides up a pulley edge | Aligner needs adjusting | Step 2 |
| Belt slips on the drive pulley | Belt too loose | Step 3 |
| Heat works but the belt won't move | Blown fuse, speed control or belt motor | Step 4 |
| Belt runs rough, jerks or skips | Chain too loose or too tight | Step 5 |
| Belt runs but no heat | Heat control or heater assembly | Step 6 |
Before any adjustment: turn the heat off, keep the belt running until the heater is at 300°F (149°C) or lower, then switch off and unplug. Do belt tracking with covers on and never leave the conveyor unattended while tracking.
Step by step
-
Check power
Make sure the dryer is plugged in. If it is and nothing works, have the building wiring checked.
-
Track the belt
With the dryer on a flat surface and the belt at full speed, watch where it sits on both rollers. Raising the belt aligner on one side moves the belt toward the opposite side; lowering it moves the belt toward that side. Turn the adjuster bolts a quarter turn at a time and give the belt time to respond. Don't let it run off a roller, or the belt can be damaged.
-
Belt tension
Tension only enough to stop the belt slipping on the drive pulley. When fitting a belt, Vastex raises both sides of the aligner equally by about 1-1/2 in, then fine-tunes the tracking.
-
Belt won't move
Unplug the dryer and check the fuse on the control plate: a 1 amp AGC fast-blow, one on 120 V models and two on 240 V models. Replace a blown fuse with the same rating. If a new fuse blows again, or the fuse is fine, the speed control or belt motor may be at fault. Vastex replaces those, so contact us.
-
Chain tension
With the chain guard removed and the dryer unplugged, move the slack part of the drive chain up and down. Total movement should be 0.25 to 0.38 in. Too tight wears the chain fast; too loose can skip a sprocket tooth. Refit the chain guard before running.
-
No heat
If the belt runs but the heater stays cold, Vastex points to a faulty heat control or heater assembly. Remember the red light comes on even when the controller has failed. Text us a photo or short video at (562) 609-4996 so we can sort out the right part.
Vastex lists abnormal vibration, noise, a strong smell or smoke as reasons to shut the dryer off and have it checked. Do that, and contact us.
Common questions
Does the belt have to be perfectly centered?
No. Vastex says it doesn't have to be perfectly centered, but it must never hang over either edge of a pulley.
How tight should the belt be?
Only tight enough to stop it slipping on the drive pulley. Don't over-tension it.
The red heat light is on but there's no heat. Is the control fine?
Not necessarily. Vastex says the red light comes on whenever the control is switched on, even if the controller has failed.
What fuse does it use?
A 1 amp AGC fast-blow fuse protects the belt drive circuit. 120 V dryers have one; 240 V dryers have two.
- Vastex D-100 and D-1000 assembly and operating instructions, doc 01-23-001E
- Vastex D1-Series and LittleRed specification sheet
- Vastex D100 product page
- AA support requests about Vastex dryers, 2024 to 2026










































































