Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex E-200 or E-2000 exposure unit not holding vacuum: what to check in order
Work through Vastex's list in order: is the pump running, is the rubber blanket torn, are the vacuum holes in the rear screen stop clear, is the pump exhaust tube clear, is the rear glass seal intact and the glass pushed tight against it, and does the lid seal touch the glass on all four sides. Most leaks come from a cut blanket, a blocked stop or glass that has slipped off its rear seal.
The vacuum pump pulls air out between the rubber blanket and the glass. Any gap, cut or blocked passage stops the blanket from pulling flat, and the stencil comes out soft. Check these in Vastex's order. Unplug the unit before you remove the glass.
Match your symptom
| What you see | Check first |
|---|---|
| Pump silent | Step 1 |
| Pump runs, blanket stays loose | Steps 2 to 4 |
| Pulls down then lets go | Steps 5 and 6 |
| Edges never seal | Step 7 |
Step by step
-
Pump running?
Start a cycle and listen. If it doesn't run, check the lid is locked (the lid limit switch stops the cycle when it's open), then contact us.
-
Blanket damage
Look over the rubber blanket for holes or cuts, especially where frame corners sit. Keep screens inside the marked area and free of sharp edges.
-
Screen stop holes
The vacuum is drawn through holes in a rear screen stop: the left stop on the E-200, the right stop on the E-2000, and all nozzles on the E2-5236. Make sure they're not blocked, then turn the pump on and feel for suction.
-
Pump exhaust tube
On the E-200 a clear tube sticks out of the left side of the cabinet; on the E-2000 it's attached to the pump under the light box. It must be unobstructed.
-
E2-5236 manifold tubes
On the 52 x 36 unit, check the four tubes between the vacuum manifold and the nozzles are connected and not pinched.
-
Rear glass seal
The glass must sit tight against the seal at the back. Try tightening the three front cams slightly. If that doesn't help, unplug, pull the glass forward, inspect the seal, then reseat the glass squarely against it and retighten the cams (see our glass cleaning guide).
-
Lid seal
A foam seal runs around the lid between the blanket and the frame. With the lid locked, check that the seal and blanket touch the glass on all four sides. If they don't, the lid needs lowering. Vastex's manual covers this, but it involves removing the lift cylinders and moving the lid in steps of no more than 1/16 in, so contact us and we'll walk you through it.
Keep the lid raised when the unit isn't in use. Vastex says it extends the life of the lift cylinders and the rubber blanket.
Still losing vacuum after all seven checks? Text a short video of a cycle to (562) 609-4996.
Common questions
How do I know the pump is working?
Turn it on and feel for suction at the screen stop nozzle (the left stop on the E-200, the right stop on the E-2000; all nozzles on the E2-5236).
Can a sharp screen frame damage the blanket?
Yes. Vastex says every surface that touches the blanket must be rounded and smooth, and screens must stay inside the marked area.
How tight should the glass cams be?
Just enough to press the glass against the rear seal. If it still leaks, tighten them a little more. Don't overtighten.
The lid seal doesn't touch the glass. Can I adjust it?
Vastex's manual shows how to lower the lid at the rear and front, in steps of no more than 1/16 in. Contact us before you try it and we'll walk you through it.











































































