Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex exposure unit setup: lid cylinders, vacuum time, exposure time and E-2000 presets
On the E-200 and E-2000, fit the two lid lifting cylinders before first use. Load the screen against the rear stops, lay the string over the frame, lock the lid, then set vacuum time so the blanket is flat before the lights start, and exposure time for your emulsion. Vastex's rough starting points with LEDs are 10 to 30 seconds for pure photopolymer and 1 to 5 minutes for dual cure, but the only reliable way to set it is an exposure calculator test.
First setup
-
Unpack carefully
Keep the lid locked closed while you lift the unit out of the crate, and don't damage the rubber blanket. Set it on a flat surface; an uneven surface can crack the glass.
-
E-2000 legs
Place the legs 28.5 in (72.5 cm) apart, lock the lid handles and, with two people, lower the unit onto them. Bolt with eight 3/8 in bolts and serrated nuts.
-
Lid lifting cylinders (E-200, E-2000)
The cylinders ship loose and strapped to the cabinet. Remove the acorn nut from the upper stud on each side of the lid, unlock and lift the lid just enough to slide each cylinder on, and refit the nuts. Snug them with a 5/8 in wrench only; don't overtighten.
-
E-20 glass
The E-20's glass is sold separately (or use 1/4 x 21 x 25 in clear float glass with polished edges; tempered is best). Slide it between the retainers and seat it against the back retainer.
Exposing a screen
-
Clean the glass
Wipe it with a lint free rag.
-
Load the screen
Place the screen with the positive attached on the glass. On vacuum units push it against the two rear screen stops and keep it inside the marked area. On the E-20, lay the pressure plate on top, with up to about 10 lb of extra weight if you like.
-
String and lid
On the E-200 and E-2000, lay the small string at the back over the screen frame, lower the lid and lock both handles.
-
Set times and start
See the controls below. The pump runs for the vacuum time, then the LEDs come on for the exposure time, then both shut off.
-
Release
Unlock the lid to break the vacuum and take out the screen.
Controls by model
| Model | How to set and start |
|---|---|
| E-20 | Rocker switch to the middle for power. Set the dial (factory scale 0 to 5 minutes, mode B). Push the switch up to start. Switch off at end of shift. |
| E-200 | Power on. Vacuum timer is factory set to a 0 to 1 minute scale, mode B. Set the exposure timer (0 to 999) with its four buttons; S means seconds, M minutes. Press start. |
| E-2000 | Power on, then use the touchscreen (below). |
On the analog timers, you can change the time scale with the RANGE SELECT screw: right increases it, left decreases it. Leave the mode set to B.
E-2000 touchscreen
-
Enter a time
On the home screen choose ENTER TIME (it defaults to 10 seconds vacuum and 10 seconds exposure). Tap the number under VACUUM, enter 0 to 999 seconds, press ENTER. Do the same under EXPOSURE.
-
Run
Press RUN. The run screen counts down. CANCEL stops the cycle. Press OK at EXPOSURE COMPLETE.
-
Save a preset
On the setup screen choose SAVE PRESET and pick a letter. Check what's already stored there before overwriting. It holds up to 10 presets.
-
Load a preset
From home choose SELECT PRESET, pick it and press LOAD.
| Message | What to do |
|---|---|
| WAITING FOR CLOSED LID | CANCEL, lock the lid down, RUN again |
| LID WAS OPENED | Keep the lid shut for the full cycle. If it opened during exposure, start again with a fresh screen. |
| POWER FAILURE | Power was lost mid cycle. If during exposure, redo with a fresh screen. |
Finding your exposure time
Vastex ranks the variables in this order: emulsion type and brand, stencil thickness (coats or capillary film), mesh color and humidity. Run an exposure calculator test whenever you change any of them. Start from 10 to 30 seconds for pure photopolymer and 1 to 5 minutes for dual cure with these LEDs. Washing out soft or losing fine detail? Text us a photo of the test at (562) 609-4996.
Common questions
How long should I expose?
It depends mostly on the emulsion type and brand, then stencil thickness, mesh color and humidity. Vastex says to determine it with an exposure calculator. Rough LED starting points: 10 to 30 seconds for pure photopolymer, 1 to 5 minutes for dual cure.
How long should the vacuum run?
Time how long the blanket takes to pull flat past the edge of your positive. On the E-200 that's typically just under a minute. If unsure, wait until it's flat to within 2 in of the frame.
What is the little string for?
Lay it over the edge of the screen frame. It helps the vacuum reach the center of the screen.
The E-2000 says WAITING FOR CLOSED LID.
Press CANCEL, lower and lock the lid, then press RUN again.
Can I use a bigger screen than the labels show?
No. Screens outside the marked area can damage the vacuum blanket. Screens must also be free of sharp edges.











































































