Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex LittleRed conveyor dryer setup and settings for curing DTG and other prints
Turn the belt on before the heat, and keep it moving while the heaters are above 300°F. The controller reads the heater, not the shirt, so the set point is hundreds of degrees above cure temperature. Vastex's starting profile for DTG on an X2D (Epson and Brother printers with pretreat) is BOOST 905°F and MAIN 500°F for 2 to 3.5 minutes in the heat. Confirm with a heat gun on the ink at the exit, still under the last heater.
Start-up, in this order
-
Power on at the main disconnect
The red Power light comes on.
-
Check the belt path
Remove anything left on the belt or in the chamber.
-
System switch on
This powers the controls, belt speed control and exhaust blower.
-
Conveyor on
Set the belt speed you plan to run.
-
Heat switch on, set the temperature
Hold the up arrow to raise the set value. Allow about 15 minutes to heat up.
Keep the belt moving whenever the heaters are above 300°F (149°C). Never leave the dryer running unattended.
Three things set your cure
Set point. The sensor sits right under the heater, so it reads far hotter than the garment. Set several hundred degrees above the ink's cure temperature, then check the real ink temperature. Heater height. Loosen the knobs on the side and raise or lower each side of the heater. Belt speed. The meter shows volts to the belt motor, not seconds. Use the table for your model, then time it yourself: put a small metal object on the edge of the belt and time it from the chamber entrance to the exit.
| Volts | X1-30 time in chamber | X2-30 time in chamber |
|---|---|---|
| 90 V | 18 s | 12 s |
| 60 V | 27 s | 20 s |
| 40 V | 33 s | 30 s |
| 30 V | 56 s | 40 s |
| 20 V | 87 s | 62 s |
| 10 V | 180 s | 135 s |
These are Vastex's figures for common sprocket and motor setups. Yours may differ, which is why the timing test matters.
Vastex starting profiles for the X2-D
| Profile | BOOST | MAIN | Heater height settings | Use |
|---|---|---|---|---|
| 2 to 3.5 minutes | 905°F (485°C) | 500°F (260°C) | 4.5 and 3.5 | Epson, Brother and other DTG printers using pretreat with DuPont white ink. Vastex notes 2.5 to 3 minutes wash tested well |
| 3.5 to 4 minutes | 860°F (460°C) | 525°F (274°C) | 3.5 and 3 | Inks and materials needing up to 4 minutes. If it overheats, lower the MAIN zone |
Vastex calls these starting points only: shop temperature, humidity, ink brand and shirt all change the result. For the X2D and X3D, Vastex's general guidance for 2 to 4 minute cures is BOOST at 800°F or more and MAIN at 500°F or more, with BOOST always equal to or higher than MAIN.
Confirm the cure
Check ink temperature regularly with a non-contact heat gun, aiming at the ink while it is still under the last heater, toward the outside of the image. A heat gun reads only the top of the ink, so allow extra on thick white underbases. Then compare with your ink maker's cure temperature and do a wash test.
Shut-down
Turn the heat switch off and let the dryer cool to 300°F or below with the belt running. Then turn the belt speed down (optional), switch the system switch to STOP, and turn off the main disconnect. Do this at the end of every shift.
Watch Vastex's video: The importance of using a donut probe
More videos
Embedded from the manufacturer's official channel.
Common questions
Is there a Vastex DTG profile for the X1 or X2 without the D?
Vastex's published DTG profile is for the X2-D. On single-zone models, start from your ink maker's cure temperature and time, set the time in the chamber with the belt speed table, and check the ink temperature at the exit. Text us and we'll help you set it up.
Can I cure DTF transfers in a LittleRed?
Vastex doesn't publish DTF settings for the LittleRed, and Color Prime lists its cure temperatures for shaker ovens and desktop curing ovens. Talk to us before running DTF film through a conveyor dryer.
Can I cure pretreatment in the dryer?
Vastex doesn't publish pretreatment settings for the LittleRed. Follow your pretreatment maker's instructions and contact us if you want to try it in the dryer.
How long does it take to heat up?
About 15 minutes to reach 700 to 800°F.
I'm taking a break. Should I turn the heat off?
If no garments will go through for more than 10 minutes, Vastex recommends lowering the set point to 500°F. It takes about 10 minutes to come back to operating temperature. Keep the belt running.
- Vastex LittleRed-X Series assembly, operating and maintenance instructions
- Vastex LittleRed X2-D profiles
- Color Prime Quick Glide Pro DTF Film specifications
- AA support requests about Vastex dryers, 2024 to 2026











































































