Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex LittleRed dryer troubleshooting: belt runs but no heat, belt drifting or slipping, error codes
When the belt runs but the dryer won't heat, the pilot lights tell you where the heat stops: the controller output light, then the red relay light, then the white heater light. If the Power light is off, look at the shop disconnect, breakers and fuses. Belt drifting is corrected at the aligner roller, half a turn at a time with the belt moving. A controller showing SbEr has lost its sensor and can run in manual mode until the sensor is replaced.
Turn power off at the external disconnect (the red Power light must be out) before opening any part of the dryer. The heaters run near 1,000°F. Any testing with power on should be done by a qualified electrician.
Match your symptom
| What you see | What to check | Go to |
|---|---|---|
| No heat, Power light off | Shop disconnect, breakers, fuses, power cord | Step 1 |
| No heat, Power light on, belt running | Control fuses, then the pilot light chain | Steps 2 and 3 |
| Heat too high or too low | Pilot lights (a relay can stick on or off) | Step 3 |
| Temperature fluctuates | Sensor location and connections, drafts | Step 4 |
| Controller shows an error code | See the code table | Step 5 |
| Belt stopped or erratic | Motor plug, chain and sprockets, obstructions, belt tension | Step 6 |
| Belt drifts to one side or slips | Belt tracking and tension | Step 7 |
Step by step
-
Power light off
Check the shop disconnect, the breaker feeding the dryer, and the power cord and its connections.
-
Power light on, no heat: fuses
The control circuit fuses are on the face of the control panel (inside the control box on older models). Check them against the fuse specs on your wiring diagram.
-
Follow the pilot lights
With the heat switch on: the control output light should cycle on and off as the controller calls for heat. The red relay output light should cycle with it, which shows the relay is switching. The white heater light (one per heater) shows electricity is flowing to that heater. Where the chain stops is where the fault is. Note what each light does and contact us; a heater that has burned out needs replacing.
-
Temperature fluctuates
Check the sensor is in its shield under the heater, clean its connections, and get rid of drafts through the chamber.
-
Read the error code
Code Meaning Fix SbEr Sensor break Replace the sensor. Use manual mode meanwhile LLEr / HLEr Reading beyond the low or high range set point Contact us to re-adjust AHEr Analog module damage Module replacement. Look for voltage spikes AtEr Auto-tune didn't run correctly Repeat auto-tune CSEr Memory values changed Controller settings need re-entering. Contact us In manual mode after SbEr, the display shows H0.00 and MAN flashes. Use the arrows to set the percentage of time the heater is on (80.0 means on 80% of the time) and keep a close eye on cure.
-
Belt stopped or erratic
Check the plug at the motor power cord, the sprockets and chain, anything blocking the belt path, and belt tension. The drive chain behind the chain guard should have no more than 1/4 in of play; it's adjusted by loosening the four motor mount bolts. Don't over-tighten it, and always refit the chain guard. A technician can check for 90 V DC at the motor plug.
-
Belt tracking and slipping
Adjust at the aligner roller with the belt moving, in small steps, and never leave it running unattended while you do. If the belt slips, raise both sides of the aligner roller equally by turning the aligner bolts clockwise. If the belt runs to the left, raise the left side; if it runs right, raise the right side, half a turn at a time. Never tighten the nut on the aligner bolt. Aim for 1 to 2 in of sag on the bottom run.
Auto-tune the controller
Needed when shop voltage isn't 240 V, or after replacing the controller, sensor or heaters. Let the heater cool below 300°F. Enter the set point first: 500°F for 120 V units, 700°F for all others. Then press and hold the scroll button until A-T shows and release; hold it again until TUNE flashes and release. When PASS appears, press scroll once. TUNE keeps flashing until it's done, which can take up to 30 minutes. Controllers changed model around November 2020, so if your screen doesn't match, contact us.
Common questions
I replaced the relay and it still won't heat.
Watch the lights with the heat switch on. If the red relay light cycles but the white heater light doesn't come on, power isn't reaching the heater: suspect a heater or its wiring. If the controller output light isn't cycling, the problem is before the relay. Text us what each light is doing.
What does SbEr mean?
Sensor break. The controller can't read the sensor under the heater and drops into manual mode. Replace the sensor. Until then you can set a percentage of on-time in manual mode and keep running.
When do I need to auto-tune the controller?
Vastex auto-tunes at the factory. Do it yourself if your shop voltage isn't 240 V (208 V, for example), or after replacing the controller, sensor or heaters.
How tight should the belt be?
Vastex wants 1 to 2 in of sag on the bottom run. You should be able to stop the rear drive pulley with moderate force on the belt, so the belt slips before the motor is damaged.
My temperature swings up and down.
Check the sensor location, clean the sensor connections, and stop drafts from fans, doors or AC blowing through the dryer.
- Vastex LittleRed-X Series assembly, operating and maintenance instructions
- AA support requests about Vastex dryers, 2024 to 2026











































































