Support
Machine type
Brand
DTF Station Vega S17

Vega S17 consumables: ink cartridges, cleaning and storage fluid, adhesive powder, film and filters

✓ Reviewed by Jason KimUpdated 3 min readFits: Vega S17
Short answer

The Vega S17 runs on its own chipped Color Prime Chroma cartridges (C, M, Y, K and two white), two cleaning cartridges, a sealed adhesive powder cartridge and 17 inch transfer film. Shake new white cartridges before inserting them, keep every cartridge above 5%, and never leave a slot empty. One powder cartridge is rated for about one roll of film. Before a shutdown of two weeks or more, the ink must be flushed out: contact us first.

What the Vega S17 uses

Supply Where it goes Notes
Color Prime Chroma ink: C, M, Y, K, white Cartridge bay, front right of the print section Chipped cartridges made for this machine. Two white slots (W1, W2).
Cleaning fluid cartridges Slots CL1 and CL2 Always installed. Also used to flush the ink lines before storage or moving.
Storage fluid cartridge Used only for long shutdowns Contact us before using it so we can confirm the steps for your machine.
Adhesive powder cartridge Finishing section Sealed TPU powder. Rated for about one roll of film at 50% coverage.
17 inch transfer film Unwinder at the back of the print section Rolls can weigh up to about 13 lb: carry them level with both hands.
Filters Finishing section, plus a mist fan filter in the print section HEPA and carbon about every 3 months, medium every 6, de-mist every 9. Replace the mist fan filter when the screen asks.

Changing an ink cartridge

  1. Have the new one ready first

    Don't leave a slot empty. An empty or missing cartridge stops the automatic cleaning. If you're out of a color, put a cleaning cartridge in rather than nothing, and contact us.

  2. Shake new white cartridges

    Hold the cartridge with the ink port facing up and tilt it side to side at about 45 degrees, two shakes per second, for 50 seconds. Don't shake hard, drop it or overdo it. Then shake each white cartridge once a day after opening, when the machine prompts you.

  3. Wipe the port and the slot, dry

    Use a dry lint-free wipe on the cartridge's ink port and the slot. Don't use cleaning liquid here: there's a circuit board close by. In the slot, wipe only the surface of the round needle housing and don't push the white plastic part in.

  4. Insert and confirm

    Push the cartridge in fully and check the status window shows its percentage, not X or NC. After a new white cartridge, print a nozzle check.

Keep every cartridge above 5%. The automatic cleaning cycles need it to run, and white below 1% can't print. A cartridge left empty for a long time can leave the heads impossible to clean.

Storing supplies

  • Ink and fluid: keep cartridges sealed until use, upright, cool, dry and out of direct sun. Don't let them freeze. Check the label for the date.
  • Film: 50 to 86°F, 35 to 65% humidity, dark and dry. Don't stack rolls on each other: it damages the coating. Trim any leading edge that's wrinkled, folded, torn or taped before loading.
  • Powder: keep the cartridge sealed until you install it.

Before a long shutdown or a move

The Vega S17 is designed to stay on. Off for 12 hours or more, the heads can clog. If it will be off for two weeks or longer, or you're moving or shipping it, the ink has to be replaced with cleaning fluid first, and the ink sumps must be emptied before it's moved. You'll need a cleaning cartridge for every channel. The machine has a built-in routine for this under Settings > Ink Path Control, but contact us before you start so we can confirm the steps and supplies for your machine. After the flush, don't uncap the heads.

To bring it back, insert ink cartridges for every channel and run Settings > Ink Path Control > Ink Charging > All Color, then print a nozzle check.

Safety

Wear gloves and safety glasses when handling ink and cleaning the machine. If ink gets in your eyes, flush with plenty of water for at least 15 minutes and get medical attention. Keep the product's safety data sheet where your team can find it. Ask us for a copy.

Questions about supplies? Text us a photo or short video at (562) 609-4996.

Common questions

Can I use other DTF ink in the Vega S17?

No. It's a closed system with chipped cartridges made for this machine. Standard bottled DTF ink won't work in it.

How long does a powder cartridge last?

It's rated for about one 100 meter roll of film at 50% ink coverage. Heavier coverage uses it faster.

How should I store ink cartridges?

Sealed, upright, cool, dry and out of direct sun. Don't let them freeze. Check the label on each cartridge for its date.

Can I swap a cleaning cartridge into a white slot?

Only as part of a procedure we walk you through. After some repairs the machine expects the exact cartridges that came out, and swapping them causes a serious error.

How should I store film?

Flat on its side in its box, at 50 to 86°F and 35 to 65% humidity, away from sunlight and dust. Don't stack rolls on top of each other.

Sources
  • DTF Station technical documentation
  • AA support requests about DTF ink, film and powder, 2024 to 2026
Did this fix it?