Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vega S17 print quality: blurry prints, banding, white shift and alignment
On the Vega S17, check the nozzle check first: most banding and blur clears with Normal or Strong head cleaning. Once nozzles are complete, use the Alignment tab: Print Position if the print lands in the wrong place, White to Color if color is shifted off the underbase, and Head Alignment for fuzzy or lined prints. Dull white usually means settled ink, so agitate the white cartridges and run 3 to 4 Strong cleans.
Start with the nozzle check
Most print quality problems are nozzles, not alignment. Print Maintenance > Nozzle Check first. If nozzles are missing, or lines in the pattern wave or bend (deflection), run Auto Head Clean at Normal, then Strong, and check again. Only move to alignment once the nozzle check is complete and straight.
Match your symptom
| What you see | Nozzle check | Do this |
|---|---|---|
| Fuzzy or blurry prints | Complete | Check the RIP (rendering intent perceptual, profile unchanged), then Head Alignment |
| Thin horizontal lines across the whole print | Complete, little or no deflection | Head Alignment |
| Thick bands in dark or gray solids | Complete | Print in one direction only, or use a higher quality mode |
| Banding at the feed pitch after a board was replaced | Complete | Feed Alignment |
| Print lands in the wrong place across the film | Any | Print Position |
| Color shifted from the white underbase | Complete | White to Color, then Head Alignment if needed |
| White looks dull | Complete or nearly | Agitate the white cartridges 2 minutes, then 3 to 4 Strong cleans |
| Colors dull | Complete | Check the RIP output profile matches the print mode |
| Several nozzles that won't recover after an ink fill | Gaps | Leave the machine on overnight, then check again |
Alignment procedures
All four live on the Alignment tab and print their patterns in the center of the film. Load film centered and run Media Set Up first. If an adjustment makes things worse, Settings > Option > Factory Reset puts the alignment values back to factory.
-
Print Position
Print Position > Print Position > Select > Print. Line the print up to the four arrows on the film: enter a minus value (down to -5.0 mm) to move toward A, or a plus value (up to +5.0 mm) to move toward B. Fold the sheet in half lengthwise and hold it up to a light: the cross should sit on the single vertical line. Press Align and repeat until it does.
-
White to Color
Print Position > White to Color > Select > Print. Find the point where white and black overlap completely and enter it. The goal is X 0, Y 0. Press Align, reprint and repeat.
-
Head Alignment
Use this when nozzles are perfect but prints are still fuzzy, lined or shifted. Head Alignment, select a head, Select, then pick the print mode and Print. You must align both print modes. In each row, find the square in the lightest color with the straightest vertical lines on both sides, and enter the number printed over it for that row. If none has straight side lines, take the one with the smallest gap. Press Align, reprint, and repeat until every row reads 0 or close to it.
-
Feed Alignment
Normally needed only after a board is replaced. Feed Alignment > Print, then find the lightest square whose horizontal lines line up on both sides. If two patterns are off in the same direction and a third in the opposite direction, the right value lies between them. Press Align and repeat until it reads 0 or close.
If prints are fuzzy and alignment doesn't settle, the gap between the head and the film may be off. That isn't an owner adjustment. Stop and contact us.
Film and room
- Film must lie flat on the print area. Never print on film that isn't flat: it causes skew and can damage the head.
- Trim the leading edge if it's wrinkled, folded, curled, torn or has tape on it.
- Run the machine at 59 to 90°F and 45 to 80% humidity. Below 45%, expect more nozzle dropout.
Send us a photo of the nozzle check (with the head numbers showing) and the problem print. Text us a photo or short video at (562) 609-4996.
Common questions
Should I run Head Alignment every time prints look off?
No. Check the nozzle check and your RIP settings first. Head Alignment is for when nozzles are complete and straight but prints are still fuzzy or lined.
My color sits slightly off the white underbase. What do I adjust?
Alignment > Print Position > White to Color. Find where white and black overlap completely, aiming for X 0, Y 0.
I made an alignment worse. Can I undo it?
Yes. Settings > Option > Factory Reset returns the head, feed and print position values to factory. Then align again.
Why does my white look dull when the nozzle check is fine?
White ink settles. Agitate the white cartridges for 2 minutes, then run 3 to 4 Strong head cleans.
A few nozzles won't come back after filling ink. Is a head bad?
Often it's air from the fill. Leave the machine on overnight so the air can settle, then check again before contacting us.
- DTF Station technical documentation
- AA support requests about Vega S17 print quality, 2026











































































