Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vega S17 maintenance: daily nozzle check and white ink, weekly cleaning, monthly grease
Leave the Vega S17 on so its automatic cleaning can run. Every day, shake the white cartridges when it asks and print a nozzle check before you print. Clean only the heads with gaps, starting with Normal. Every week, clean the maintenance unit, left ink sump, media guide and nozzle cover, and brush the heater bed. Once a month, re-grease the guide rods and wipe the powder level sensor.
Every day
-
Keep it on and keep it error free
The machine cleans itself only when it is on, has no error showing, has at least 5% ink in every cartridge, the waste bottle isn't full, and the covers and ink bay are closed. If a message says automatic maintenance can't run, fix the cause right away. Pressing Yes only hides it for 5 minutes.
-
Shake the white cartridges when prompted
The machine asks every 12 hours, then beeps hourly until you do it. Pull each white cartridge, wipe the port and slot with a lint-free wipe, then shake it with the port facing up, side to side at about 45 degrees, two shakes per second, for 50 seconds. The countdown on screen shows when you're done. Put the cartridges back in the same slots.
-
Print a nozzle check before you print
Go to Maintenance > Nozzle Check. Note the head number beside any block with gaps or wavy lines.
-
Clean only the heads that need it
Go to Maintenance > Auto Head Clean, tap the head number, choose Normal and press Cleaning. Print another check. Use Strong only for larger gaps or wavy lines, because it uses more ink. If 3 to 5 Strong cleanings don't help, leave it for 6 hours or more and try again.
Every week (the machine reminds you every 7 days)
Wear gloves and eye protection. Use only the machine's own cleaning liquid and applicators.
-
Maintenance unit, media guide and left ink sump (about 10 minutes)
Press Maintenance > Regular Maintenance. The carriage moves to the center. Open the top cover. With a damp applicator, gently wipe the moisturizing caps and the suction cap (top, sides, then inside) without bending them, and check the rims for dried ink. If a part inside the suction cap shifts, press it back down until the spring bottoms out. Then wipe the wiper cleaner gently (its lever is thin and breaks easily), both faces of the wiper, and all the way around the roller. Wipe the media guide gently without pressing hard, and clean any ink off the top of the left ink sump.
-
Nozzle cover (about 15 minutes)
This is the one cleaning job that can damage a head if it's done wrong. Remove the left ink sump (one screw), then with a fresh damp applicator wipe only the nozzle cover surface and its stepped edge. Use a dry applicator for the sides of the head, the screw hole area and the spring at the back. Never let liquid stay on the head: dry it off when you're done. Put the sump back and make sure its latch is engaged.
If every color block on your next nozzle check has white lines running through it, stop printing and contact us. That pattern points to liquid inside the head, not a clog.
-
Close up and check
Close the top cover and press Yes. The carriage parks and caps. Run Auto Head Clean, then a nozzle check.
-
Heater bed in the finishing section
Power off the finishing section and wait for the bed to cool. Wear gloves and a mask. Open the right front door and the heater door, brush powder off the top of the bed and the underside of the media guide with the supplied brush, and remove all the loose powder. If brushing doesn't clear it, use the supplied squeegee. Never scrape with metal. Close the doors, and don't switch the finishing section back on while a job is printing.
Every month
- Guide rods (about 30 minutes): from Regular Maintenance, wipe the old grease off both rods, then put a tiny dot of the supplied guide rod grease at each marked point and spread it along the top of the rod. Slide the carriage slowly by hand, a few round trips, staying out of the maintenance unit area. Wipe off any excess and keep grease off the sensors. Move the carriage to the left end before you close the cover. If you print 5 days a week for 7 to 8 hours a day, do this more often.
- Powder level sensor: in the finishing section, behind the acrylic cover inside the front left door. Wipe it with a lint-free wipe. A caked sensor misreads the powder level and can cause poor adhesion.
When the machine asks
- Waste ink bottle: empty it, clean any dried ink off the tube tip, stand it back upright with the tube straight, and only then press Waste Ink Reset in the status window. Resetting without emptying makes it overflow.
- Filters: the HEPA and carbon filter about every 3 months, the medium filter about every 6, and the de-mist filter about every 9. Contact us for replacements.
Stuck on a step? Text us a photo or short video at (562) 609-4996.
Common questions
How hard should I shake the white cartridges?
Not hard. With the ink port facing up, tilt side to side about 45 degrees at two shakes per second for 50 seconds. Shaking too hard or too long can cause leaks.
Normal or Strong cleaning?
Start with Normal on just the head with gaps. Use Strong for bigger gaps or wavy lines. If 3 to 5 Strong cleanings haven't cleared it, wait at least 6 hours and try Strong again.
A couple of white nozzles are missing. Do I need to clean?
Usually not. A few missing white nozzles don't show in prints. Missing CMYK nozzles do, so clean those.
Can I use isopropyl alcohol on the print section?
Use only the cleaning liquid and applicators made for this machine on the print section. Other products can damage the heads.
I'm closing the shop for a week. What do I do?
Leave it on with ink in it. For two weeks or more, or if you're moving it, the ink lines need flushing first. Contact us before you start.
- DTF Station technical documentation
- AA support requests about DTF printer clogs and maintenance, 2024 to 2026











































































