Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Viper MINI not spraying, not pulling pretreat or dripping: flushing and tip care
A Viper MINI that runs but won't pull pretreat almost always has dried pretreat in the line or on the spray tip. Flush it with warm or hot clean water using the priming method (wheel off the table, cup under the nozzle, hold Spray), and clean the tip only with the soft toothbrush. Viper warns that pretreat left inside will make the MINI inoperable, so flush every day and any time it sits for more than 30 minutes.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Motor runs, but no pretreat comes through the tube | Line out of the liquid, or pretreat dried in the line | Steps 1 and 2 |
| Spray is weak, narrow or spits | Pretreat dried on the spray tip | Steps 2 and 3 |
| Drops land on the shirt | Pretreat built up on the front spray side | Step 4 |
| Drips constantly, even with Spray released | Not covered in Viper's guide | Contact us |
Step by step
-
Check the supply line
Make sure the filtered end of the fluid line sits fully under the liquid and the line is pushed firmly into the MINI.
-
Flush with warm or hot water
Take the line out of the pretreat and put it in a container of warm or hot clean water. Hold the MINI so the drive wheel isn't touching the table or a shirt, hold the spray cup under the nozzle, and press Spray until clean water runs through and sprays out. Viper also suggests pulling the line out of the liquid and running it briefly to push air through, then flushing with hot water again. Repeat until the spray comes out full and even.
-
Clean the spray tip
Remove the nozzle with a half twist. Scrub the tip with the soft toothbrush that came with the MINI and rinse it. Never use toothpicks, needles or anything hard: Viper says they damage the tip for good. If the spray is still uneven, fit the spare tip from the box.
-
Wipe the front of the machine
Pretreat that collects on the front spray side, body, height slide or wheels can drip onto the next shirt. Wipe it off during production and at the end of the day.
-
Test with water before pretreat
Once water sprays evenly, put the line back in pretreat, refill the line the same way, and spray a test shirt.
Stop it happening again
- Flush with warm or hot water at the end of every day you use it. Viper warns that pretreat left in the MINI will damage it and make it inoperable.
- If you'll set it down for more than 30 minutes, flush it with water first.
- Never let pretreat dry on the spray tip.
If clean water won't pass at all, the MINI keeps dripping with the button released, or the drive wheel doesn't move it smoothly, stop and text us a short video at (562) 609-4996. Don't open the body.
Watch Viper's video: Viper MINI introduction and use
Embedded from the manufacturer's official channel.
Common questions
The motor runs but nothing comes through the tube. What do I do?
Check the line end is under the liquid, then flush with warm or hot water as in step 2. If water won't come through either, text us a short video at (562) 609-4996.
Can I use a pin to open the tip?
No. Viper says only the included soft toothbrush. Toothpicks or needles damage the tip so it won't spray properly.
How long can it sit with pretreat in it?
Viper says to flush with water if you won't use it for more than 30 minutes, and never let pretreat dry on the tip.
It drips onto my shirts. Why?
Usually pretreat that has collected on the front spray side. Viper says to wipe it during production. If it keeps dripping when you're not pressing Spray, contact us.
My spray solenoid stopped working. Can I get a replacement?
The original MINI spray solenoid listing is discontinued, so text us and we'll check what fits your unit.
- Viper MINI Quick Start Manual Version 3: filling, cleaning and flushing, cleaning and care
- Viper MINI support page
- AA support requests about the Viper MINI clogging, leaking and not pulling pretreat, 2024 to 2026











































































