Support
Machine type
Brand

xTool MetalFab weld settings: filler wire or not, wire by metal, wire feeder, scan width and thickness limits

✓ Reviewed by Jason KimUpdated 2 min readFits: MetalFab Laser Welder 1200W · 800W
Short answer

On the MetalFab, skip filler wire for sheet under 1 mm or small gaps and weld autogenously; otherwise match the wire to the base metal (308L for 304 stainless, ER70S-6 for mild steel, 4043 or 5356 for aluminum). Keep the wire no smaller than the gap. Use a wider scan width for aluminum and wide gaps, and a narrow one for stainless and tight joints.

Most MetalFab weld quality comes down to three choices: whether to use filler wire at all, which wire, and how wide the beam oscillates (the scan width). These are xTool's published recommendations.

Do you need wire?

Not always. For sheet under 1 mm, or for small gaps, xTool says you can melt the base metal directly (autogenous welding) with the autogenous welding nozzle. Use wire and the default welding nozzle for thicker plate, wide gaps, repairs and joints that need extra strength.

Match the wire to the metal

Base metal Grade Wire
Stainless 304 308L
Stainless 316 316L
Stainless 430 309L
Carbon steel Q235, 20# ER70S-6
Carbon steel 45# ER50-6
Galvanized DX51D, DX52D ER70S-G or ER70S-6
Aluminum 6061, 6063 4043
Aluminum 5052 5356
Brass H62 S221

Shielding gas is 99.99% nitrogen or argon (argon preferred on aluminum). xTool's sizing rules: the wire diameter should not be smaller than the gap, and the workpiece should not be thinner than the wire. As a guide, xTool suggests 1.2 mm wire for metal 2 mm and thicker, and 0.8 mm wire for 1 mm and under.

Wire feeder

  • Supported wire: 0.8, 1.0, 1.2 and 1.6 mm. Fit the feed rollers for your wire size, both rollers the same, and set the roller tensioners to the matching position.
  • Spool limits: up to 15 kg on the 1200W feeder, 5 kg on the 800W.
  • Retracting wire: open the side door, press the retraction button while turning the spool (a loose spool unravels), and pinch the wire by hand as the end leaves the rollers so it does not spring loose.

Scan width

Situation xTool's range
Aluminum, copper (conduct heat) 1.0 to 2.0 mm
Stainless (holds heat) 0.3 to 0.8 mm
Gap under 0.5 mm 0.5 to 1.0 mm
Gap over 1.0 mm 1.5 to 3.0 mm

Standard and Advanced modes

The 1200W starts in Standard mode: pick the material, thickness and wire diameter and weld. Advanced mode, with the Professional option, opens up manual fine-tuning. Start from Standard and change one setting at a time on scrap.

How thick can it weld through?

Metal Full penetration up to
Stainless steel 5 mm
Carbon steel 5 mm
Galvanized steel 5 mm
Aluminum 4 mm
Brass 3 mm

Thicker sheet can still be joined; these are the depths xTool says it fully penetrates. Avoid marking or engraving brass and aluminum with the welder: reflected laser light can permanently damage the machine.

Galvanized steel releases zinc fumes. Lower the power, keep inert gas coverage steady, remove the zinc at the joint first, and use fume extraction and a NIOSH-approved respirator.

Need help dialing in a joint? Text us a photo of the weld and your settings at (562) 609-4996.

Watch xTool's video: replace the MetalFab welding wire

More videos

How to change the MetalFab nozzles
Replace the wire feeding nozzle

Embedded from the manufacturer's official channel.

Common questions

Do I always need the wire feeder?

No. For material under 1 mm or small gaps, xTool says you can weld without filler wire.

Which wire for 304 stainless?

308L, per xTool's table.

Can I run 0.8 mm and 1.2 mm wire on the same feeder?

Yes, with the matching pair of feed rollers and the tensioners set for that size.

Can I engrave with the welder?

xTool says it can mark, but not on highly reflective metals like brass and aluminum, which can reflect the beam and damage the machine.

Did this fix it?