Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool MetalFab status light, laser won't fire, black smoke, sticking wire and porous welds
The MetalFab only fires when the interlock key loop is closed, lasering is enabled and the grip sensing button is held: then the ring blinks green slowly. Solid red with three beeps is a fault to report. For sticking filler wire, raise the laser shutdown delay or lower the re-feeding delay; for black smoke, clean the metal, check gas coverage and inspect the lens protector.
When the MetalFab will not fire or the welds look wrong, start with the ring light on the main unit (the welding head shows the same color), then work through the matching section.
Match your symptom
| What you see | Likely cause | Go to |
|---|---|---|
| Solid white, trigger does nothing | A firing condition is not met | Won't fire |
| Solid red, three beeps | Fault or exception | Red light |
| Black smoke while welding | Material, dirt, wire, technique or lens | Smoke |
| Wire sticks in the weld | Delay settings | Wire sticking |
| Pores in aluminum welds | Oxide, moisture, gas | Porosity |
| Big, blurry red aiming spot | Cleaning lens left in the head | Wrong lens |
Won't fire
The laser only fires when all three conditions are met. Then the ring blinks green slowly and the trigger works.
-
Safety interlock loop closed
The key in the package is both the access key and the remote interlock connector. Check it is fitted. Removing it disables processing.
-
Lasering enabled
Check laser emission is enabled on the welder's screen.
-
Grip sensing button pressed
Hold the welding head so the grip sensor is pressed, then pull the trigger.
Also check the emergency stop is released. If the wire will not feed while welding, both the screen's Wire Feed Enable and the torch's wire feed enable switch must be on.
Red light
Solid red with three beeps means an exception or malfunction. Note any message on the screen, stop, and contact us with a photo of the screen. The welder does not export logs, so the screen message matters.
Smoke
xTool lists five causes of black smoke during welding:
- Material: aluminum alloys smoke more by nature.
- Dirty surface: oil, grease or oxide on the metal. Clean it first.
- Wire: standard wire not made for laser welding fumes more; xTool suggests low-fume wire.
- Technique: wrong torch angle, too little shielding gas, or wrong power leave the weld poorly covered.
- A damaged lens scattering the beam. Check the lens protector.
Wire sticking
If the filler wire sticks to the weld when you release the trigger, increase the laser shutdown delay or reduce the re-feeding delay.
Porosity in aluminum
- Clean off the oxide layer and contamination, and make sure the metal is completely dry.
- Use argon; it reduces porosity on aluminum better than nitrogen.
- Raise the wire feed speed if needed.
Wrong lens
The MaxClean accessory uses a cleaning lens in place of the normal lens protector. Before any welding or cutting, look at the red aiming spot: if it is large and blurry, the cleaning lens is still in. Swap the lens protector back before you weld or cut. xTool warns that welding or cutting with the cleaning lens, especially CNC cutting, risks damaging the machine.
Galvanized steel gives off zinc fumes. xTool advises lower power, inert gas, local removal of the zinc where you weld, fume extraction and a NIOSH-approved respirator.
For anything else, text us a short video at (562) 609-4996.
Watch xTool's video: clean or replace the MetalFab lens protector
More videos
Embedded from the manufacturer's official channel.
Common questions
The ring is solid white. Is it broken?
No. Solid white means powered on but not ready. Close the interlock loop, enable lasering and hold the grip sensor.
Why is my aiming spot big and fuzzy?
The MaxClean cleaning lens is probably still in the head. Swap the lens protector back before welding or cutting.
Can I see error logs?
No. xTool says the welder does not export logs or processing data, so photograph the screen message.
Will the laser lose power on long jobs?
xTool says the 1200W holds stable output for extended periods under normal conditions.











































































