Support
Machine type
Brand

xTool MetalFab setup checklist: power circuit, shielding gas, regulator, fittings, workspace and safety gear

✓ Reviewed by Jason KimUpdated 2 min readFits: MetalFab Laser Welder 1200W · 800W
Short answer

Before the MetalFab arrives, have an electrician confirm a dedicated circuit (xTool recommends 220 V, 25 A or more for the 1200W), and get 99.99% nitrogen or argon with a flow valve set to 15 to 30 L/min for welding. The gas inlet is a 3/8 in push-to-connect fitting, so a US 1/4 in outlet needs a metal adapter rated above 1.2 MPa. Plan for clearance, fume extraction, a metal welding table, 1080 nm laser goggles and hearing protection.

xTool publishes a preparation checklist for the MetalFab, and almost every first-day problem traces back to something on it: the wrong circuit, no regulator, the wrong hose size. Work through it before the welder arrives. Nothing here replaces xTool's safety training video, which every operator should watch first.

1. Space

  • Unpacking: at least 50 cm (19.7 in) clear on all four sides of the crate.
  • Running: 30 to 50 cm (11.8 to 19.7 in) clear at the front and back of the welder for heat.
  • Room for the gas cylinder or generator and a metal welding table. Add the CNC Cutter's footprint if you have one.

2. Power

  • 1200W: 200 to 240 V, about 4200 W at full power, 21 A maximum. xTool recommends a dedicated 220 V, 25 A or higher circuit and a 30 A or 50 A breaker ahead of the welder to suit your installation. US units ship with a NEMA 6-50P or L6-30 plug.
  • 800W: 220 to 240 V, 13.5 A, 3 kW full load.
  • Have a licensed electrician confirm the circuit. Never use a standard household circuit, never share the circuit with other welders or heavy equipment, and only use the power cable supplied with the machine.

3. Gas

Job Gas Setting
Welding 99.99% nitrogen or argon 15 to 30 L/min, or 0.1 to 0.2 MPa (14.5 to 29 PSI)
Handheld cleaning 99.99% nitrogen or argon 15 to 30 L/min, or 0.1 to 0.2 MPa
Handheld cutting Nitrogen, argon or compressed air Over 0.8 MPa (116 PSI)

For aluminum, xTool prefers argon to reduce porosity. Titanium needs argon.

4. Regulator and fittings

  • A flow valve is the easiest way to set welding and cleaning flow. A pressure-reducing valve set to 0.1 to 0.2 MPa also works for welding.
  • You need an adjustable wrench and Teflon tape to fit the regulator to the cylinder without leaks.
  • The welder's gas inlet is a 3/8 in (10 mm) push-to-connect fitting. A US 1/4 in cylinder outlet needs a 1/4 to 3/8 in adapter: pure metal, rated above 1.2 MPa (174 PSI).
  • Secure the cylinder on a cart or similar so it cannot fall.

5. Work area and extraction

  • A metal welding table, ideally with clamps so plates do not weld to the bench.
  • An exhaust system for metal fumes and dust, or discharge outdoors.
  • A controlled area: xTool's Class 4 guidance calls for restricted access, a laser warning sign at the entry, and a Laser Safety Officer who writes your site's operating procedure.

6. Protective equipment

  • Laser safety goggles for 1080 nm (one pair comes in the box). xTool's safety training asks for optical density above 6 for everyone in the area.
  • Heat-resistant gloves (included).
  • N95, KN95 or P100 masks (you supply).
  • Hearing protection: over 90 dB at full power.

7. Wire

The 1200W comes with a spool of 1 mm stainless steel wire for stainless. Buy matching wire for other metals; our MetalFab wire and settings guide has xTool's table.

Do not power up or fire the laser until the circuit has been checked by an electrician, the gas is connected and leak-free, and everyone in the area is wearing goggles.

Questions about a particular step? Text us at (562) 609-4996.

Watch xTool's video: MetalFab laser welding safety training

More videos

MetalFab Laser Welder 1200W unboxing and first use
MetalFab Laser Welder 800W unboxing and first use

Embedded from the manufacturer's official channel.

Common questions

What plug does the US 1200W use?

xTool lists a NEMA 6-50P or NEMA L6-30 plug for US units.

Can I share the circuit with my MIG welder?

xTool recommends a separate circuit from other welding equipment.

Flow valve or pressure regulator?

Either for welding: 15 to 30 L/min on a flow valve, or 0.1 to 0.2 MPa on a pressure-reducing valve. Handheld cutting needs over 0.8 MPa.

Can I use compressed air?

For handheld cutting and cleaning, yes, though xTool says nitrogen or argon cleans brighter. For welding, use 99.99% nitrogen or argon.

Did this fix it?