Support
Machine type
Brand
DTF Station Aries 213 and Aries 113 UV DTF printers

Aries UV ink, varnish and print head care: shaking, varnish settings, missing nozzles and U1 heads

✓ Reviewed by Jason KimUpdated 2 min readFits: Aries 213 · Aries 124 · Aries 113
Short answer

Shake UV ink before pouring, and give white and varnish a full 60 seconds. Keep white ink circulation running. Recover missing nozzles with a fill or charge on the affected head and a light cleaning, not repeated heavy cleaning. Varnish and ink amounts are adjusted in Pilot, in small steps with a test print each time. Aries replacement heads must be the UV (U1) version for your model.

Handling UV ink and varnish

  • Shake before you pour. Aries 213: colors 5 to 10 seconds, white and varnish a full 60 seconds, then rest 5 minutes. Aries 124: every bottle at least 20 seconds, white 60 seconds, then rest at least 3 minutes. The rest lets bubbles rise.
  • Vent the bottle. Open it with one pour hole and one small vent hole.
  • Match the labels. Pour each ink into the tank with the matching cap label.
  • Keep white moving. White ink circulation should be on whenever the printer is on. If you leave the printer on the emergency stop for a week, circulation keeps running.
  • Keep cleaners separate. Only UV DTF cleaning solution touches the ink path, caps and wiper.

Adjusting varnish and ink output in Pilot

  1. More color, white or varnish

    Open Pilot and go to Advance > Print Configuration > Rip Multi-Ink. Each of Color, White and Varnish starts at 1. Raise the one you need by 1 or 2, click OK and Save, then test print. Repeat until the output is right.

  2. Less varnish on the Aries 124

    There are two ways, and it's worth testing both. In Spot Color, enable it, select V (varnish), choose RIP, lower the ink amount (start at 50%) and Save. Or in Spot Color > Image > Identical Ink, lower the ink amount and Save. The RIP method reduces it in processing, the Image method at the nozzles.

  3. Leave these alone unless we ask

    Keep Auto Clean on Close (off). Leave Spot Color unchecked when you're not using it for varnish reduction, because it can conflict with the RIP. Doubling white with Global Ink slows printing dramatically.

If transfers lift off with the A film when you peel, the varnish may be too thin. Don't reduce varnish below what your transfers need to release cleanly.

Recovering missing nozzles

Nozzle check shows What to do
A few gaps after the printer sat idle Run two head cleanings, then check again.
Gaps on one head (Aries 124) Run Fill Ink on that head for 30 seconds, cancel, run one cleaning and check again. Or run 2 light cleanings on just that head.
More than 10% missing (Aries 213) Run more ink charge cycles and cleanings, then check again.
The same channel missing every time Contact us. We'll walk you through swapping two dampers to find out whether it's the head or the ink path.
Only one block of white printing, or a channel cutting out mid-print Contact us. Ink on a head cable can cause this, and it needs checking before you swap parts.

Before you call, take a clear photo of the nozzle check with white paper under the film.

Choosing a replacement head

The Aries 213 uses one Epson i3200 U1 head, and the Aries 124 uses four Epson i1600 U1 heads. U1 is Epson's UV version. The water-based A1 heads used in DTF printers look the same but are made for different ink, and the two aren't interchangeable. Aries 113 heads differ from both: text us your serial number before ordering. After any head replacement, the calibration has to be redone. We'll walk you through it.

Questions? Text us a photo or short video at (562) 609-4996.

Watch DTF Station's video: Aries 124 how to reduce varnish

Embedded from the manufacturer's official channel.

Common questions

Should I turn on Auto Clean in Pilot?

Leave it set to Close (off), which is the default for the Aries UV printers.

How much should I reduce varnish on the Aries 124?

Start at 50% in the Spot Color settings, test, and adjust from there.

My white or varnish is too thin. Can I increase it?

Yes. In Pilot, raise the White or Varnish value under Print Configuration > Rip Multi-Ink by 1 or 2, test print, and repeat until you're happy.

Can I put a DTF printer head in my Aries?

No. Epson makes UV (U1) and water-based (A1) versions of these heads. They aren't interchangeable. The Aries 213 uses an i3200 U1 and the Aries 124 uses i1600 U1 heads.

One color keeps disappearing even after cleaning. Is the head dead?

Not necessarily. It may be the damper, ink line, filter or ink. We can walk you through a test that tells which.

Sources
Did this fix it?