Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson F2270 error messages: what each one means and what to do
Most F2270 messages point to a cleaning job or a loading problem: the sensor cover or encoder scale needs wiping, or the media is wrinkled, too thick for the spacer setting, or something has fallen inside. For Maintenance Request or a printer error with a code, write the code down, turn the printer off, unplug the power cable at both ends, reconnect it and power cycle a few times. If the same code returns, contact us with the code.
Match your message
| Message on the screen | What to do |
|---|---|
| It is time to clean the sensor cover / The Sensor Cover cannot be recognized | Clean the sensor cover now (select the message, then Cleaning). Until you do, the printer may not print at the right head height. Repeat if it still isn't recognized. |
| It is time to clean the Encoder Scale | Clean the encoder strip right away, or print quality drops. See our maintenance guide. |
| Printing has stopped. Check whether there is an obstruction | Reload the media flat with no wrinkles, check the spacers and platen height suit it, check nothing has fallen into the printer, then select OK. |
| Cannot move the movable base | Remove anything on the platen that isn't the media, reload it flat, check spacers and height, and clear anything that fell around the movable base. |
| Failed to inspect the condition of nozzles. Cannot run Auto Cleaning | Run a manual cleaning: Light first, then Medium, then Heavy. |
| The printer has exceeded the temperature at which normal operation is guaranteed | Cool the room, then start again. Epson's operating range is 50 to 95°F. |
| No reprint data found | Reprint needs a USB stick in the printer. |
| Cannot use the inserted Memory Device | The stick may be damaged, full, or over 999 files, or was pulled out while in use. Try another stick. |
| Combination of the IP address and subnet mask is invalid | Enter the correct network values. Ask whoever runs your network if you're not sure. |
| Recovery Mode | A firmware update failed. Connect by USB and run the update again. |
| Maintenance Request: Replace Parts Soon / End Of Parts Service Life (code) | A part is at or near the end of its life. Write down the code and contact us. The message stays until the part is replaced, and if you keep printing a printer error will follow. |
| Printer error. Turn the power off and on again (code) | Follow the steps below. |
Printer error codes: step by step
-
Write down the code
Take a photo of the screen. The printer stops printing on its own.
-
Unplug and reconnect
Turn the printer off, unplug the power cable from both the outlet and the printer, and plug both ends back in firmly. A loose power cable is one cause Epson lists.
-
Power cycle a few times
Turn it on and off several times. Afterwards, let it stay on until the head is capped, because a head left uncapped dries out.
-
Still there? Contact us
If the same code comes back, text the code and photo to (562) 609-4996.
Thick garments and the platen height
Most T-shirts are about 2 mm thick. For those, use both spacers A and B with the lever at P (only spacer B on the sleeve or medium-grooved platen). For anything thicker, load the garment flat, select Menu > Platen Height Adjustment, set the lever to 8 and select Start. If a height message appears, change the spacers:
| Garment thickness (standard or hanger platen) | Spacers |
|---|---|
| 6 to 12 mm | A only |
| 12 to 16 mm | B only |
| 16 to 24 mm | Remove both |
Then move the lever left one notch at a time until the height error beeps, and back right one notch until it stops. Select OK, then Done, and tighten the fixing lever.
Common questions
Printing has stopped on every hoodie.
Hoodies and sweatshirts are usually thicker than 2 mm. Run Menu > Platen Height Adjustment and change the spacers to suit the thickness, as shown on this page.
The sensor cover message comes back right after cleaning.
Repeat the cleaning. Epson says to clean it again if the printer reports the sensor cover can't be recognized, and to use ink cleaning solution if water doesn't remove the stains.
Are the red and green lights in the sensor safe to look at?
Yes. Epson says they're LEDs and can't harm your eyes.
A firmware update failed and the printer says Recovery Mode.
Connect the computer and printer with a USB cable and run the firmware update again.
What does my error code number mean?
Epson doesn't publish code meanings for owners. Follow the power-cycle steps, and if the code comes back, text it to us with a photo of the screen.
- Epson F2270 User's Guide: Product status messages
- Epson F2270 User's Guide: Checking spacer combinations and platen height
- Epson F2270 User's Guide: Cleaning the sensor cover
- Epson F2270 User's Guide: Cleaning the encoder strip
- Epson F2270 User's Guide: Cleaning the print head
- Epson F2270 User's Guide: Environmental specifications
- AA support requests about F2270 errors, 2024 to 2026











































































