Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson F3070 clogged nozzles and weak white ink: Epson's cleaning order and what to check next
Run Auto Cleaning first, then Light, Medium and Heavy on just the rows with gaps. If gaps keep returning, clean the suction caps and around the heads, then check the flushing pads and anti-drying caps for hardened ink. For thin white with a good nozzle check, look at White ink shaking, pre-treatment and the heat press, then run Cleaning(Heavy) on the White rows and, if needed, switch to Color ink mode and back.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Gaps in one or two rows of the nozzle check | Partial clog | Steps 1 and 2 |
| Gaps that keep coming back after several cleanings | Dirty suction cap, lint on the metal edges, hardened flushing pads or worn anti-drying caps | Steps 3 to 5 |
| Nozzle check is fine but white is thin or uneven on the shirt | Settled White ink, pre-treatment or heat press | Step 6 |
| White still thin after all of that | Sediment in the White ink path | Step 7 |
| Ink drips or smudges on the shirt | Lint or ink lumps around the suction cap or head | Steps 3 and 4 |
Step by step
-
Print a nozzle check
Use transparent film or colored paper in White ink mode, letter or A4, on the standard M platen at position P (or position 3 with the medium grooved platen, using thick paper). Choose Menu > Maintenance > Print Head Nozzle Check. The labels under each block tell you which row is which, such as C1.
-
Clean in Epson's order
Choose Menu > Maintenance > Head Cleaning. Run Auto Cleaning first. If gaps remain, run Cleaning(Light), then Cleaning(Medium), then Cleaning(Heavy). Use Select Nozzles to clean only the rows with gaps, and print a check after each level.
-
Clean the suction caps
Epson says nozzles won't clear while the suction cap is dirty, however many cleanings you run. Use Cleaning the Maintenance Parts > Suction Cap, remove lumps with the plastic tweezers, and wipe until you can see the cap's own color around the edges. See our F3070 daily and weekly maintenance guide for the full procedure.
-
Clean around the heads and the metal edges
Fibers stuck to the metal edges can touch the head and stop ink firing. Run Cleaning the Maintenance Parts > Around the Head, wipe the metal edges with a damp, well wrung cloth, and clean around each head with a fresh wide stick and ink cleaner. Then run head cleaning again.
-
Check the flushing pads and anti-drying caps
Turn the printer off, open the right cover and lift each flushing pad. If you can't clearly see the mesh because waste ink has hardened on it, replace the pads. Then run Around the Head again, and when the head moves, look inside the front and back anti-drying caps. If ink has collected in them, replace both from Replace Maintenance Parts > Anti-Drying Cap. Always replace from that menu so the counter stays right.
-
For thin white with a good nozzle check, check the basics
Shake the White units at the start of every working day. Make sure the pre-treatment is even and not too diluted, and that the shirt was pressed completely dry. A heat press loses temperature when you press shirts one after another, and too little pressure leaves fibers standing and white uneven. If a pre-treated shirt has sat for a while, press it for a few seconds before printing. Also check the white density in Garment Creator 2 and that the ink isn't past its date or a year in the printer.
-
Run Heavy on the White rows, then a mode round trip
Choose Menu > Maintenance > Head Cleaning > Cleaning(Heavy) > Select Nozzles > White, select all the WH rows and select OK. If white is still thin after one or two runs, switch Printer Mode to Color ink mode and back to White ink mode. You'll need two Cleaning ink supply units and two White units. If white is still thin after that, contact us.
Every cleaning uses ink and fills the waste bottle. Don't keep repeating Heavy. Epson's own limit before escalating is two Heavy cleanings.
When a row just won't clear
Menu > Maintenance > Print Head Nozzle Limitation lets you keep printing with only the upper or lower half of the nozzle rows. It's slower and can reduce quality, so Epson recommends it only as a stopgap until the head is fixed. Mark the half where you see the clog, White first, then Color.
If steps 1 to 5 don't fix it, Epson's self-repair guide says the printer's diagnosis decides whether a print head actually needs replacing. That's done in a User Self-Repair mode that Epson reserves for trained people. Text us your nozzle check photos at (562) 609-4996 and we'll take it from there.
Watch Epson's video: cleaning around the F3070 print heads and metal edges
Embedded from the manufacturer's official channel.
Common questions
How many Heavy cleanings should I run?
Epson's self-repair guide says to run Cleaning(Heavy) once, and if the clog isn't cleared, one more time. If it still isn't clear after the suction cap, metal edges and anti-drying caps are taken care of, contact us.
Does the F3070 have to print white during maintenance even if I only print color?
Yes. In White ink mode, White ink is used during maintenance even if you only print with color ink.
Can I keep printing with a row that won't clear?
Temporarily, with Print Head Nozzle Limitation. It uses half the nozzle rows, so printing is slower and quality can drop.
Is my print head bad?
Not necessarily. Epson says the printer's diagnosis may find that changing a setting or a Heavy cleaning fixes it. Send us your nozzle checks before ordering anything.
Why is white weak after the printer sat in Color ink mode?
Epson says White density can be low after a long time in Color ink mode. Run Cleaning(Heavy) on the White rows first.
- Epson SC-F3000 Series (SureColor F3070) User's Guide (PDF)
- Epson SC-F3000 Series: How to Replace the Print Head, User Self-Repair (PDF)
- Epson F3070 Required Maintenance (PDF)
- Epson Video Manuals: Cleaning around the print head and the edges of the metal (SC-F3000 Series)
- Epson Garment Creator 2 Operation Guide (PDF)
- AA support requests about F3070 clogs and white ink, 2024 to 2026










































































