Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson F3070 error messages: sensor cover, print head strike, maintenance requests and printer error codes
Most F3070 messages ask for routine care: clean the sensor cover or suction cap, shake the White ink, or reload a wrinkled shirt flat. For a Printer error with a code, unplug the power cable at both ends, reconnect it and power cycle a few times. If the same code returns, or you see a Maintenance Request with a 16 digit code, write the code down and contact us.
Match your message
| Message on the screen | What it means and what to do |
|---|---|
| It is time to clean the Sensor Cover. / The Sensor Cover cannot be recognized. | The clear sensor covers are dirty, so the printer can't find the platen position or set the right head height. Select Cleaning (or Menu > Maintenance > Cleaning the Maintenance Parts > Sensor Cover), open the left cover and wipe each clear cover with a clean-room wiper dampened in water, then dry it, until you can see clearly inside. If the message comes back right away, the cleaning wasn't enough: do it again, using ink cleaner on the wiper if water doesn't lift the ink. |
| It is time to clean the Suction Cap. | Clean the suction caps now. If this shows up often, contact us. |
| Ink shaking is needed. | The White units haven't been shaken for 24 hours. Pull the tray and shake it right away. |
| You need to replace Ink Supply Unit. | Replace it. Epson says to replace a White unit immediately, because leaving the printer in this state can damage the print head. |
| Printing has stopped. Check whether there is an obstruction inside the printer | Reload the garment so it's flat with no wrinkles. For thick garments check the platen position and head height. Make sure nothing has fallen into the printer, then press OK. |
| Printing has stopped. The print head may strike the media. | Usually the shirt swelled during printing. Make sure the pre-treatment is completely dry before you print. On big, ink-heavy designs printed with a platen frame, removing the frame can let slack spread out; if you do, reduce the white under-base width in Garment Creator 2 or your RIP so it stays inside the image, and don't touch the shirt while it prints. |
| Cannot move the movable base. Check around the movable base | Remove anything on the platen other than the garment, reload a lifted or very wrinkled shirt flat, check the platen position suits a platen you just changed, and clear anything that fell around the base. Then press OK. |
| The surface of the media cannot be detected. (after a "media surface is too high" message) | Set Media Settings > Platen Gap to Auto and change Head Height to Standard or Wide. |
| Failed to inspect the condition of nozzles. Cannot run "Auto Cleaning". | Run Head Cleaning manually: Light first, then Medium, then Heavy. |
| Printer has exceeded the temperature at which its operations are guaranteed | Bring the room back into range, then start again. Epson recommends 59 to 77°F. |
| The combination of the IP address and the subnet mask is invalid. | Enter the correct network values. Ask whoever manages your network if you don't know them. |
| Maintenance Request: Replace Parts Soon / End Of Parts Service Life, with a 16 digit code | A part is near or at the end of its life. The message stays until the part is replaced, and if you keep printing a printer error follows. Write down the code and send it to us. See the print head codes below. |
| Printer error. Turn the power off and on again. (code) | Follow the steps below. |
Print head end of life codes
Epson's self-repair guide says these 16 digit maintenance codes mean a print head has reached the end of its service life:
- 0000020000000000: the color head (front)
- 0000040000000000: the white head (back)
- 0000060000000000: both heads
Any other code needs your dealer or Epson to read it. Head replacement is a User Self-Repair job that Epson says only people trained in User Self-Repair should do, so text us the code and a photo before anyone touches the head.
Printer error codes: step by step
-
Write down the code
Take a photo of the screen. The printer stops printing on its own when this error appears.
-
Disconnect and reconnect power
Turn the printer off, unplug the power cable from both the outlet and the printer, then plug both ends back in firmly. A loose cable is one cause Epson lists. Also check the ink unit is plugged in.
-
Power cycle a few times
Turn it on and off several times. Then leave it on until the head is capped (parked at the right side). A head left uncapped can dry out and clog for good.
-
Still showing the same code?
Text the code and the photo to (562) 609-4996.
Other things that look like errors
- Emergency stop button pressed: once it's safe, turn the button as you pull it out, then turn the printer off and immediately back on so the head can cap.
- Red light inside the printer: normal. It's an internal light, not a fault. The red and green lights behind the sensor cover are LEDs and are safe to look at.
- Screen keeps going dark: that's sleep mode. Press any button. You can change it under Menu > General Settings > Basic Settings > Sleep Timer.
- Print count stays at 1/1: jobs sent from a Garment Creator Easy Print System hot folder don't show the count on the panel, even when several prints are set.
Watch Epson's video: cleaning the F3070 sensor cover
Embedded from the manufacturer's official channel.
Common questions
What does a Maintenance Request code mean?
A part is near or at the end of its service life. Epson doesn't publish what most codes mean, but its self-repair guide says 0000020000000000, 0000040000000000 and 0000060000000000 are print head end of life codes. Send us the code.
Can I keep printing with a Maintenance Request showing?
The message stays until the part is replaced, and Epson says a printer error follows if you keep using the printer. Plan the repair now.
Why does it say the print head may strike the media?
The garment swelled during printing, usually because the pre-treatment wasn't fully dry. Dry shirts completely in the heat press before printing.
I cleaned the sensor cover but it still says it can't be recognized.
Epson says that means the cleaning wasn't enough. Clean both covers again, using ink cleaner on the wiper if water doesn't remove the ink.
Can I replace the print head myself?
Epson publishes a User Self-Repair procedure, but says only people trained in User Self-Repair should do it. Text us first.
- Epson SC-F3000 Series (SureColor F3070) User's Guide (PDF)
- Epson SC-F3000 Series: How to Replace the Print Head, User Self-Repair (PDF)
- Epson F3070 support page
- Epson Video Manuals: Cleaning the sensor cover (SC-F3000 Series)
- AA support requests about F3070 errors, 2024 to 2026











































































