Support
Machine type
Brand
Epson SureColor F3070

Epson F3070 daily, weekly and monthly maintenance: White ink shaking, suction cap and head cleaning

✓ Reviewed by Jason KimUpdated 4 min readFits: F3070 · SC-F3000 Series
Short answer

Every day, shake the White ink supply units, print a nozzle check and clean only the rows with gaps, starting with Auto Cleaning. Every week, clean both suction caps and around the print heads from Menu > Maintenance > Cleaning the Maintenance Parts. Every month, shake the color units and check for firmware updates. Leave the printer switched on, and replace parts from the menu when it asks.

Every working day (about 5 minutes)

  1. Shake the White ink supply units

    White ink settles fast. Before you start printing each day, pull out each White (WH) tray with one hand under it, then tilt it up and down at about 60 degrees, about 5 times in 5 seconds, and push it back in. If the units go 24 hours without a shake, the screen shows Ink shaking is needed. Do it right away. A tray whose lamp is flashing blue also needs shaking. Don't swing the trays hard, or ink can leak.

  2. Print a nozzle check

    Bring the platen forward and tape the check sheet in place: transparent film (such as OHP film) or colored paper in White ink mode, plain paper in Color ink mode, letter or A4 size. Use the standard M platen or an L/M hanger platen with the platen position at P; the S hanger, XS and sleeve platens can't print a check pattern. Set Platen Gap to Auto, then choose Menu > Maintenance > Print Head Nozzle Check, pick All, White Only or Color Only, and select Start.

  3. Clean only if you see gaps

    Choose Menu > Maintenance > Head Cleaning. Run Auto Cleaning first: the printer checks its own nozzles and picks the strength. If gaps remain, run Cleaning(Light), then Medium, then Heavy, on just the rows that are missing (the labels under each block of the check pattern tell you which row is which). Print another check after each one.

Leave the F3070 switched on. Epson says it runs maintenance every time it powers up, so turning it on and off often uses more ink. Never cut power at the plug or breaker while it's on, or the head may not cap.

Every week (10 to 15 minutes)

  1. Clean the suction caps

    Wear gloves, eye protection and a mask. Choose Menu > Maintenance > Cleaning the Maintenance Parts > Suction Cap and select Start. The platen and head move to the maintenance position. Open the right printer cover. Lift off any lump or film of dried ink with the plastic tweezers that came with the printer (never metal tweezers). If the four small holes in the cap are blocked, clear them with the tweezers without pushing the waste into the holes. Then, using separate sticks for the front and back caps, wipe the inside with a thin cleaning stick dampened in ink cleaner while rotating it, and wipe the outside and top edge with a wide stick. Keep wiping the edges until you can see the cap's own color. Don't rub hard, and wipe off any cleaner that drips onto the anti-drying caps with a dry stick. Close the cover and select Done.

  2. Clean around the print heads and the metal edges

    Choose Menu > Maintenance > Cleaning the Maintenance Parts > Around the Head. When the platen moves, open the right cover and wipe the metal edges with a soft cloth wetted in water and wrung out hard, then wipe them dry. Do the same on the left side. When the head moves to the maintenance position, open the maintenance cover and use a new wide cleaning stick soaked in ink cleaner to remove ink, lint and dust from the parts around each head, one stick for the front head and another for the back. Never touch the nozzle surface. Close the cover and select Done, then print a nozzle check.

A buzzer sounds 10 minutes after the head moves out and every 10 minutes after that. Have your sticks, cleaner and tweezers laid out on a tray before you start so the head isn't left uncapped.

Every month

  • Pull out each color tray (not WH, Maintenance Liquid or Cleaning) and shake it about 5 times in 5 seconds.
  • Check Epson's F3070 support page for new firmware and software.
  • Check the flushing pads and air filters for hardened waste ink or heavy dirt.

When the printer asks

Message What to do
It is time to clean the Suction Cap. Clean it now (above). If this message keeps coming back quickly, contact us.
It is time to clean the Sensor Cover. Select Cleaning and follow the screen. Wipe the clear cover with a clean-room wiper dampened in water, then dry it, on both sides. Until you do, the printer can't find the platen and can't print.
Head Cleaning Set is at the end of its service life. Replace the wiper unit and both flushing pads together from Menu > Maintenance > Replace Maintenance Parts > Head Cleaning Set. Check the waste liquid port for hardened ink, and make sure both pads click in flat. Raised hooks can damage the head.
Anti-Drying Cap is at the end of its service life. Replace the front (color) and back (white) caps together from the same menu, and remove the protective cover from the new caps before you print.
Air Filter is at the end of its service life. Replace all three filters at once: one under the right cover and two under the left.
Waste Ink Bottle is at the end of its service life. Swap the bottle and select OK to reset the counter. If you swap it early, start from Replace Maintenance Parts > Waste Ink Bottle so the counter stays correct.

Always start a part replacement from the menu, even when no message is showing, so the life counters stay right. Use only the ink cleaner from the maintenance kit, and only pure water where Epson says water. Never use alcohol or tap water, and never move the head or platen by hand.

Stuck on a step? Text us a photo or short video at (562) 609-4996.

Watch Epson's video: cleaning the F3070 suction cap

Embedded from the manufacturer's official channel.

Common questions

Should I turn the F3070 off at night?

No. Epson recommends leaving it on. It runs maintenance each time it starts, so frequent power cycling uses more ink.

How hard do I shake the White ink?

Gently. Tilt the tray up and down at about 60 degrees, about 5 times in 5 seconds, at the start of each day. A new White unit gets about 25 times in 25 seconds when you install it.

Why can't I see white on my nozzle check?

White doesn't show on white paper. Print the check on transparent film or colored paper when the printer is in White ink mode.

Can I clean the caps with water or alcohol?

No. Use the ink cleaner from the maintenance kit on the caps and around the heads. Epson says mixing ink with water or solvents makes it harden. Water is only for the metal edges and the sensor cover.

The suction cap message keeps coming back. Is that normal?

Epson says to contact your dealer if it appears frequently. Text us a photo of the cap after cleaning.

Did this fix it?