Support
Machine type
Brand
Epson SureColor F6370

Epson F6370 error messages, paper jams and banding: what Epson says to do

✓ Reviewed by Jason KimUpdated 3 min readFits: F6370
Short answer

Most F6370 messages have a simple fix: reseat the chip unit for a Chip Unit Error, tape the paper back to the core for a Reel Unit Error, and load paper at least 10 inches wide for a Paper Size Error. For a Call For Service, unplug the printer from both ends, reconnect and restart several times, then contact us with the code. For banding, clean the head, align it, then run Paper Feed Adjust for that paper.

Messages and what to do

Message What to do
Prepare empty waste ink bottle The waste bottle is nearly full. Have a new one ready.
Chip Unit Error, not recognized Remove and reinstall the chip unit. Let ink reach room temperature (at least four hours) in case of condensation. Use only chip units from Epson ink packs for this printer. If it repeats, replace the chip unit.
Check Ink Levels The chip unit is nearly used up. Check the tank level against the metal plate or the pack scale and refill if needed.
Command Error Press pause/cancel, choose Job Cancel, and check your RIP supports this printer.
F/W Install Error Turn off, wait a few minutes, turn on, and reinstall the firmware with Epson LFP Remote Panel 2.
Take-up Error Turn off, wait a few minutes, turn on. If it persists, contact us.
Reel Unit Error Paper didn't wind correctly. See below.
Reel Unit Disconnected Reconnect the take-up reel cable, choose No to power off, wait, and turn back on. Choose Yes to print without it.
Paper Cut Error Press OK, pull the paper out, cut it with scissors, pull the edge straight out and press OK.
Paper Size Error Remove the paper and load paper at least 10 inches wide. If it's already wide enough, turn off Paper Size Check and try again.
Maintenance Request A part is near or at end of life. Note the code and contact us.
Call For Service See below.

Reel Unit Error

Set the take-up reel's Auto switch to Off. If the leading edge came off the core, tape it back on. If the error came up mid-print, press the down arrow to feed paper, cut after the last print, remove the paper from the reel, fit a new core, tape the paper to it, set Auto to Backward and press OK.

Call For Service

The printer stops printing. Turn it off, unplug the power cable from both the wall and the printer, reconnect both ends and turn it on and off several times. If the same code comes back, text a photo of it to (562) 609-4996. A loose power cable can also trigger this, so make sure it's pushed fully in.

Clearing a paper jam

  1. Restart

    Turn the printer off, wait a moment and turn it on. You'll be asked to open the printer cover.

  2. Cut the damaged paper

    Pull the paper toward you and cut off torn or creased paper from the roll. Press OK.

  3. Clear the head

    Open the printer cover, move the print head away from the jam by hand, and press OK. Hold the down arrow to eject the cut paper and remove it.

  4. Reload

    Close the cover, press OK, and reload when the screen asks. Cut the roll's edge straight first, and cut off any wavy or creased part.

To stop repeat jams, don't use curled, creased or folded paper, check the paper and settings match, and if paper won't eject, make sure Paper Suction isn't set too strong.

Banding, grainy prints and stains

What you see Try this
Gaps or faint colors Nozzle check, then head cleaning. Still clogged after the strongest cleaning: leave it off overnight and check again
Grainy or blurry Head alignment for that paper
Dark or pale stripes Paper feed adjustment
Stains or rubbing Clean the head, wiper and caps; raise Platen Gap
  1. Head alignment

    Load the paper you'll print on and pick its setting in Custom Paper Setting. Go to Paper > Custom Paper Setting, choose that paper, then Head Alignment. Pick Manual(Bi-D) for bidirectional printing (try Manual(Uni-D) if it doesn't help) and press OK to print the pattern. Choose the pattern with the fewest white lines in each row and enter the values.

  2. Paper feed adjustment

    Go to Paper > Custom Paper Setting, choose the paper, then Paper Feed Adjust > Pattern and print it. Measure the distance between the + marks (average the left, center and right) and enter it. Use the same paper, width, tension and take-up setup you print with.

  3. Fine-tune while printing

    During a print, press the cut/feed media button. Press up if you see dark bands, down if you see pale bands, then OK when it looks right.

Keep the covers closed while printing. Opening them stops the head suddenly and causes uneven color.

Common questions

What does Chip Unit Error mean?

The chip unit isn't being read. Remove and reinstall it. Condensation can cause it, so let ink sit at room temperature for at least four hours. If it keeps happening, replace the chip unit.

My prints have dark or light stripes. Which adjustment fixes that?

Paper feed. Dark bands mean too little feed, so raise it; pale bands mean too much, so lower it. You can adjust during printing with the cut/feed media button.

Prints are grainy or blurry. What should I run?

Head alignment, from Custom Paper Setting for the paper you have loaded.

What does Maintenance Request mean?

A part is near or at the end of its life. Note the code on the screen and contact us. Once it says replace now, you can't keep printing without a service call.

Is the red light inside the printer a fault?

No. Epson says it is always on and is normal.

Sources
Did this fix it?