Support
Machine type
Brand
Epson SureColor F6470 and F6470H

Epson F6470 banding, misaligned lines and error messages: head alignment, media feed adjustment and what each message means

✓ Reviewed by Jason KimUpdated 3 min readFits: F6470 · F6470H · SC-F6400 Series
Short answer

On the F6470, horizontal lines or wrong colors start with a nozzle check and head cleaning (Auto, then Light, then Heavy), then capping station and wiper cleaning. Grainy prints or misaligned vertical lines need Print Head Alignment, and dark or pale bands need Media Feed Adjustment, both under Media Settings > Print Adjustments for the paper you have loaded. For a printer error, unplug and reconnect the power at both ends, restart several times, then contact us with the code.

Match your symptom

What you see Do this
Horizontal lines or wrong colors Nozzle check and head cleaning, then capping station and wiper cleaning
Ink drops on prints Head cleaning, then head maintenance kit cleaning
Grainy, or vertical lines misaligned Print Head Alignment
Dark or pale bands Media Feed Adjustment
Uneven color Keep the cover shut while printing; shake the ink
Scuffed or rubbed prints Raise Platen Gap; widen margins

1. Clear clogs first

Alignments don't work on clogged nozzles. Print a nozzle check, then run Auto Cleaning. If that doesn't clear it, run Cleaning (Light), then Cleaning (Heavy). If three cleanings don't help, clean the capping station and wiper (or, for ink drops, run the print head cleaning with the head maintenance kit). Our F6470 capping station guide has both procedures.

2. Print Head Alignment

Use this for grainy prints and for vertical ruled lines that don't line up in bidirectional printing. Paper must be at least 10 inches wide.

  1. Load paper as you'll print

    Load the paper the way you'll actually use it. If you use the take-up reel, attach the paper to the core first. Make sure the right media number is selected.

  2. Print the pattern

    Go to Menu > Media Settings > Print Adjustments > Print Head Alignment and press Start. Wait for it to finish.

  3. Read #1A

    In each #1A pattern, find the number where the lines are finest (they overlap). If more than one #1A prints, average them and round to a whole number.

  4. Enter and repeat

    Enter that value with the arrow buttons. Do the same for #1B, #2A and #2B, then press OK.

3. Media Feed Adjustment

Use this for horizontal banding, tint unevenness or stripes. Manual(Standard) needs about 190 mm of paper; Manual(Measurement) about 1090 mm.

  1. Start it

    With paper loaded as you'll print, go to Menu > Media Settings > Print Adjustments > Media Feed Adjustment, choose Manual(Standard) and press Start.

  2. Pick the best pattern

    Two groups print, A and B. In each, choose the pattern with the least overlap or gap. If two tie, use the value between them. If every pattern has overlaps or gaps, pick the best one and run it again until one is clean. If ink bleeding makes them unreadable, enter 0.0% once and use Manual(Measurement).

  3. Measurement method

    For Manual(Measurement), cut off the printed patterns #1 and #2, lay them flat, measure with a scale that reads to 0.5 mm, and enter both values.

  4. Fine-tune during a job

    While printing, press the adjust-while-printing area on the home screen. If you see dark bands, increase the feed; pale bands, decrease it. Epson recommends running the full adjustment from the menu after that job.

Messages and what they mean

Message What to do
Media not attached to roll core Set Auto to Off. Tape the paper back to the core, or cut after the last print, remove the roll, fit a new core and tape it. Set Auto to your winding direction and press OK.
Take-up Reel Unit cannot be recognized Reconnect its cable to the printer and restart. Choose No to keep printing without it.
Unsupported media size Paper must be at least 10 inches wide. If it is, try turning off Width Detection.
IP address and subnet mask invalid Check the values with whoever runs your network.
Recovery Mode A firmware update failed. Connect by USB (not network) and run the update again.
Maintenance Request A part is near or at end of life. Note the code and contact us.
Printer error Turn off, unplug the power at the wall and at the printer, reconnect, and turn on several times. If it repeats, contact us with the code.
Motor self adjustment running Normal. Wait and don't turn it off.

The red light inside the printer is normal. Still banding after all of this? Text a photo of the print and the nozzle check to (562) 609-4996.

Common questions

Dark stripes or pale stripes: which way do I adjust?

Dark bands mean the paper isn't feeding far enough, so increase the feed. Pale bands mean too much feed, so decrease it.

Manual(Standard) or Manual(Measurement)?

Use Standard normally. Use Measurement if banding remains after Standard, if the pattern is hard to read because ink bleeds, or if you need accurate print length.

Do I have to align again for each paper?

Yes. Adjustments are saved to the media setting you have selected, so do them once for each paper and after changing that setting's advanced options.

Why does the printer run a cleaning when I turn it on?

After a long time unused, it may clean automatically. Epson says it ends after about 5 to 7 minutes.

Why is color ink used when I only print black?

Head cleaning uses ink from all colors.

Did this fix it?