Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson F6470 ink shaking reminders: how often, how to shake, and replacing ink supply units
The F6470 reminds you to shake High Density Black every week and the other colors every three weeks. Open the message, press How To..., and tilt the unit in its tray at about 60 degrees about 5 times in 5 seconds. Shake a new unit about 10 times in 10 seconds before installing it. Settled ink causes uneven tint and clogs, so shake as soon as the message appears.
Why the F6470 asks you to shake its ink
Epson says the F6470's ink settles slowly in the ink supply units. Settled ink causes uneven tint and clogged nozzles. So after a unit is installed, the printer reminds you to take it out and shake it on a schedule:
| Ink | Shake reminder | How |
|---|---|---|
| High Density Black | Once every week | About 5 times in 5 seconds |
| All other colors (including F6470H special inks) | Once every three weeks | About 5 times in 5 seconds |
| Any unit, when you replace it | Every replacement | About 10 times in 10 seconds |
The ink status area on the home screen shows an icon when a unit is due. When the message appears, shake it right away.
Shaking a unit
-
Open the message
On the home screen press the status of consumables area. In the Message List, press the message saying it's time to shake the ink, then press How To... to see the steps on screen while you work.
-
Shake it in its tray
Leave the unit in its ink supply unit tray. Tilt the tray up and down at about 60 degrees, about 5 times in 5 seconds. Don't shake or swing it hard, because ink can leak.
-
Put it back
There may be ink around the supply port, so keep it off the printer and your surroundings. Slide the tray back in. Every tray must hold a unit, or the printer won't print and may malfunction.
Replacing a unit
-
Replace before the job, not during it
If a unit runs out mid-print you can replace it and carry on, but Epson says colors may look different where the ink dried at different times. Swap a low unit before you start a big job. You can reuse the removed unit later until it's empty.
-
Prepare
If you use the auto take-up reel, cut the paper first. When the replace message is showing, press How To... and follow the screen. To swap early, move the lock switch for that color to unlock it, then press How To....
-
Shake the new unit and install
In its tray, tilt the new unit up and down at about 60 degrees, about 10 times in 10 seconds, then install it and lock it.
Storing and using ink
- Use ink before the expiry date on the package or one year after installing it, whichever comes first.
- Store units at room temperature out of sunlight. A unit brought in from the cold needs more than four hours at room temperature before use.
- You can remove a unit and reinstall it later; its chip keeps track of the ink left. The supply port has a valve, so it doesn't need a cap, but keep it free of dust.
- Don't touch the chip, drop the unit or take it apart. Small particles you may see are ink components, not dirt.
- The printer stops before a unit is completely empty to protect the head. That's normal.
If the F6470 will sit unused, Epson says to turn it on at least once every six weeks so it can clean the head, and not to switch it off until that cleaning finishes.
Ink not recognized after a swap? Text a photo of the screen to (562) 609-4996.
Common questions
Do I take the ink out of the tray to shake it?
No. Epson says to shake it while it sits in the ink supply unit tray.
How long does ink last once installed?
Epson recommends using it before the package expiry date or within one year of installation, whichever comes first.
Can I swap a unit in the middle of a print?
Yes, but colors may look slightly different. Epson suggests replacing a low unit before you print.
I see small particles in the ink. Is it contaminated?
Epson says ink supply units contain components that help maintain print quality, and these aren't foreign bodies.
The printer says a unit is empty but it isn't. Why?
To protect the print head, the printer stops before the ink is completely used up.
- Epson SC-F6400 / SC-F6400H Series (SureColor F6470 / F6470H) User's Guide
- Epson SureColor F6470 support page
- Epson F6470 FAQ: do I need to perform any maintenance
- AA support requests about Epson sublimation ink, 2024 to 2026











































































