Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson F7200 loading transfer paper, using the auto take-up reel, clearing jams and common error messages
Load paper on the F7200 just before you print, center the roll using the label under it, push both roll holders fully into the core and tighten them, then feed the paper over the platen and set the media holding plates on its edges. Epson recommends taking up with the printable side in on paper 36 inches or wider. A Take-up Error means the paper isn't attached properly: switch Auto off and back, then reattach it.
Match your symptom
| Symptom | Go to |
|---|---|
| Starting a new roll | Load a roll of transfer paper |
| Take-up Error or paper winding crooked | Attach the paper to the take-up reel |
| Paper jammed or creased | Clear a paper jam |
| A message on the screen | Common messages |
Load a roll of transfer paper
-
Get ready
Turn the printer on and wait for Load media. Open the front cover and slide the media holding plates out of the way by their tabs. Full rolls are heavy, so lift them with two people.
-
Set up the roll holders
At the back, loosen the roll holder screws, slide the holders wider than the roll and center the roll supports between them. Set the roll on the supports with its left edge lined up to the position on the label under the roll.
-
Lock the roll in
Raise the left lift lever and push the left holder firmly into the core, then tighten its screw. Do the same on the right, push the center of the holder twice, and tighten. Turn the handle until part A is hidden, then stop. A loose holder makes the paper slip and causes banding.
-
Feed the paper
Raise the media loading lever, feed the paper past the pressure roller, lower the lever, and check the left edge crosses the square on the loading label. If it doesn't, take it out and load it again.
-
Bring it to the front
Open the front cover, raise the lever, pull the paper straight to the front edge of the after heater, and close the cover. Use the arrow buttons to pull it back to the edge of the front cover and check it's straight and taut. Epson suggests a Media Suction setting of 2.
-
Set the plates and settings
Lower the lever. Slide the media holding plates onto the paper edges so the round holes are centered over the edges. Leave them at the sides if the media is thicker than 0.4 mm. Close the cover, confirm or change the media settings and pick the roll type.
Attach the paper to the take-up reel
-
Prepare the core
Use a take-up core the same width as the paper. Set Auto to off, hold the down arrow to feed paper to the core holders, line the right holder up with the right edge, fit the core and tighten both holders.
-
Tape it
For printable side in, take the paper over the guide bar and behind the core. Tape the center first, pulling the paper straight, then each side, so it lies flat.
-
Wind and check
Use the Manual switch to wind it on. Tap both sides lightly to check the tension is even and the edges line up, then set Auto back on.
Clear a paper jam
-
Turn off
Open the front cover and turn the printer off. Slide the media holding plates to the sides. If a plate is bent, replace it before carrying on.
-
Free the paper
If the head is over the paper, move it away gently by hand. Raise the loading lever, pull the paper to the cutter groove and cut off the creased part. Rewind the roll and remove any scraps.
-
Restart
Turn it on, reload the paper, and print a nozzle check. Don't leave the printer off with the head uncapped.
Common messages
| Message | What to do |
|---|---|
| Take-up Error | Switch Auto off, then back, and reattach the paper to the core |
| Media Size Error | Use paper at least 300 mm wide. If the width is right, turn off Media Size Check |
| Command Error | Cancel the job and check that your RIP supports the F7200 |
| F/W Install Error | Turn off, wait a few minutes, turn on and update the firmware again |
| Maintenance Request | A part is near the end of its life. Note the code and contact us |
| Call For Service | Unplug from both ends, reconnect and restart. If it repeats, note the code and contact us |
If paper keeps feeding crooked after a move, Epson's fix is a two-person parallel adjustment of the feeder and take-up reel. Text us at (562) 609-4996 and we'll walk you through it.
Common questions
What is the narrowest paper the F7200 takes?
300 mm (11.8 in). Narrower rolls trigger Media Size Error. Epson recommends 36 in or wider when you use the take-up reel.
My prints have banding near the edges. Could it be the plates?
It can be. Epson says wrongly placed or damaged media holding plates can cause banding and stripes, and deformed plates can damage the head. Replace them if they're bent.
The paper wrinkles in the after heater. What helps?
Check Feeding Tension and Feed Speed for that paper, lower the take-up tension if you print thin paper at heavy coverage, and make sure the after heater isn't too hot.
The screen says Call For Service with a code. Can I fix it?
Turn the printer off, unplug it from the wall and the printer, reconnect and turn it on. If the same code returns, note it and contact us.
Should I leave paper loaded overnight?
No. Epson says to load paper just before printing, because the pressure rollers can crease it, and creased paper can jam or rub the head.
- Epson SureColor F7200 User's Guide (PDF)
- Epson SC-F7200 Series User's Guide CMP0048-03 (PDF)
- AA support requests about Epson wide-format media loading and media holding plates, 2024 to 2026











































































