Support
Machine type
Brand
Epson SureColor F7200

Epson F7200 weekly maintenance: cap cleaning kit, cleaning around the print head, wiper and waste ink bottle

✓ Reviewed by Jason KimUpdated 3 min readFits: F7200
Short answer

Epson changed the F7200's schedule so the caps and the area around the print head get cleaned once a week, not just when quality drops. Clean the caps with the clear cap cleaning liquid from the Epson Cap Cleaning Kit, never with the brown ink cleaner from the maintenance kit. Use the ink cleaner only around the print head, and clean or replace the wiper when prints smudge or gaps keep coming back.

What to do and when

When Job
Once a week Clean around the print head and clean the caps. Stir the High Density Black ink
Smudges or gaps return Clean the wiper and its attachment points
Wiper worn Replace the wiper and wiper cleaner together if the wiper is torn or ink has soaked the back of the wiper cleaner
Bottle full Replace the waste ink bottle

Two different liquids are used. The clear cap cleaning liquid (Cap Cleaning Kit) is for the caps only. The brown ink cleaner (maintenance kit) is for around the print head and the wiper. Putting ink cleaner on the caps can make the printer malfunction.

Before you start

  • Take the transfer paper out of the printer.
  • Wear the gloves from the kit, eye protection and a mask.
  • Touch something metal to discharge static.
  • Use only the cleaning sticks from Epson's kits, use a fresh stick each time, and don't touch the stick tips.
  • Never use water or alcohol on the nozzles, caps or wiper.

Move the head for maintenance

Never push the print head by hand. With the printer on, press the maintenance button, choose Head Maintenance and press OK. The head moves to the left so you can reach the caps and wiper. If you're still working after 10 minutes, an alarm sounds as a reminder.

Clean around the print head

  1. Prepare the ink cleaner

    Pour about 10 ml of ink cleaner into the kit's cup on a tray and close the bottle. Dip a fresh stick and let the excess drip off.

  2. Wipe around the head

    Open the left maintenance cover. Wipe ink, lint and dust from around the print heads, wiping in one direction only.

  3. Clean between the nozzle rows

    With a small stick dampened in ink cleaner, wipe gently in one direction between the nozzles. Don't press on the nozzles or scrub back and forth.

  4. Use the cleaning wiper

    Wet all sides of the cleaning wiper's blade with a large stick and ink cleaner, then pull it once across the head surface. Don't wipe back and forth. Repeat with fresh sticks if ink remains, then close the left cover.

Clean the caps with the Cap Cleaning Kit

  1. Open the right cover

    Once the head has moved to the left, open the right maintenance cover.

  2. Wipe the outsides

    Hold a new, dry narrow stick straight up and down and wipe ink from around the outside of all 6 caps and the guide section. Don't touch the inside of the suction cap on the far left.

  3. Fill the anti-drying caps

    Pour about 5 ml of cap cleaning liquid into the kit's cup. With the dropper, put 2 to 3 drops into each of the 5 anti-drying caps (every cap except the far left one) until they're full. Never drip liquid into the suction cap, and if you do by mistake, don't try to wipe it out.

  4. Soak it up

    Soak up the liquid with a new, dry wide stick. Use a second new wide stick to remove what's left.

  5. Finish

    Close the right cover and press OK twice to return the head. Print a nozzle check before your next job.

Clean or replace the wiper

Open the right cover, hold the wiper by its attachment point, tilt it left and lift it out. Clean the front, back and bottom with a large stick and ink cleaner, clean the attachment points inside, then press it back in until it clicks. If the wiper is split or worn, replace it and the wiper cleaner at the same time: press the new parts down until they click, close the cover and press OK to finish.

Replace the waste ink bottle

When you see Prepare empty waste ink bottle, get a new one ready. When it says to replace it, wait until the printer isn't printing or cleaning, then:

  1. Remove the full bottle

    Raise the ink splash guard, lift the bottle out of the holder, and seal it with its inner seal and cap. Leave the ink in it for disposal.

  2. Fit the new bottle

    Put the waste ink tube into the new bottle, set it in the holder and lower the splash guard so it seals the bottle's mouth.

  3. Reset the counter

    Press OK, then OK again to reset the waste ink counter. If you swapped it early, use Waste Ink Counter in the maintenance menu.

Keep the waste ink bottle in place whenever the printer is on, and even when it's off, because ink in the tube can still drip. If cleaning doesn't bring the nozzles back, text us a photo of the nozzle check at (562) 609-4996.

Watch Epson's video: F7200 cap cleaning with the cap cleaning kit

Embedded from the manufacturer's official channel.

Common questions

Can I use the brown ink cleaner on the caps?

No. Epson's 2016 supplement says to use only the clear cap cleaning liquid on the caps, because the brown ink cleaner from the maintenance kit can make the printer malfunction.

How often should I clean the caps?

Once a week. Epson changed this from "when print quality declines" to weekly in its maintenance supplement for the F7200.

An alarm keeps sounding while I clean. Is something wrong?

No. If the head stays in the maintenance position for 10 minutes, the printer beeps to remind you. Finish, close the cover and press OK to bring the head home.

Can I clean the caps or wiper with water or alcohol?

No. Epson says not to use water or alcohol on the nozzle surface, caps or wiper.

Head cleaning won't clear a missing color. What next?

Clean around the print head, the wiper and the caps, then print another nozzle check. If gaps stay, text us the nozzle check photo.

Did this fix it?