Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson F7200 refilling ink and replacing the chip unit: Check Ink Levels, Chip Unit Error and the Charge and Reservation settings
On the F7200 you refill an ink tank from one whole ink pack and fit that pack's chip unit at the same time. When Check Ink Levels appears, look at the tank: refill only once the ink is 70 mm (2.8 in) or less from the bottom of the tank. After Epson's firmware update you can also reserve the next chip unit in advance, and the printer switches to it on its own.
Match your message
| Message | What it means |
|---|---|
| Check Ink Levels | The chip unit's ink is nearly used up. Check the tank level and get a pack ready |
| Chip Unit Error (reattach or replace) | Take the chip unit out and put it back. If it repeats, use a new chip unit. Condensation can also cause it: let the ink sit at room temperature for 4 hours |
| Chip Unit Error (match label) | The chip isn't from a pack specified for this printer. Use only Epson packs for the F7200 |
| Refill Ink Tank | If more than 70 mm of ink is left, the tank itself needs replacing. Contact us |
If a chip unit error or warning shows, don't pour in the ink from the pack that chip came with until you've cleared the message. Doing so can mix up colors.
Before you refill
- Wear gloves and eye protection.
- Let packs that were stored cold sit at room temperature for 4 hours.
- Open a pack only when you're ready to pour, and pour all of it into one tank.
- Don't remove the ink tanks or put anything on them.
- Use up ink within 25 days of refilling, or by the date on the pack.
Refill a tank and replace the chip unit
-
Check the level
When Check Ink Levels appears, hold the scale on the ink pack against the tank. If more than 70 mm (2.8 in) of ink remains, keep printing until it drops to that line.
-
Pull out the slider
Lift the lock lever on that color's slider, put a finger in the groove on top and pull it straight out. Keep it level so the chip unit doesn't drop.
-
Swap the chip
Check that the slider's label color matches the new pack. Take off the old chip unit and fit the one supplied with the new pack.
-
Reinsert the slider
Hold it level, slide it in without forcing it, and lower the lock lever.
-
Shake the pack
Shake the new pack side to side about 5 cm (2 in) for 5 seconds, about 15 times.
-
Open the tank
Open the ink inlet cover and remove the inlet cap. On the High Density Black tank, lift the cap slowly by its loop and rest the stirring stick on the tab at the edge of the tank.
-
Pour
Gently tear or cut the spout seal, set the spout in the groove and tilt slowly until the pack is empty. Don't squeeze the pack.
-
Close up
Replace the inlet cap (for High Density Black, guide the stirring stick back into the tank first). Press the cap down firmly so the slider can't catch it, then close the cover.
Stir High Density Black once a week
High Density Black settles in its tank. Once a week, open its inlet cover, lift the cap by the loop and move the stirring stick slowly up and down 15 times, from the bottom of the tank to the top. Replace the cap firmly and close the cover.
Using chip reservation (after the firmware update)
Epson added Charge and Reservation features in a firmware update. When you fit a new chip unit, the printer stores (charges) one pack's worth of ink and shows it as blue bars. You can then slide the next new chip unit in early. It stays reserved and charges the printer automatically when the current charge runs out.
- The ink still goes in only when the tank is at 70 mm or less. Don't open the pack early.
- If you remove a reserved chip before it charges, the reservation is cancelled but the chip is still usable.
- A raised lock lever stops the reserved chip from charging. Lower it.
- A used or partly used chip can be reserved, but Epson recommends a new one because its ink amount is unclear.
If the charge display and the real tank level drift apart, Epson added Printer Setup > Charge Setting. Use Extend Charge Timing when the charge runs out before the tank reaches 70 mm, and Forced Charge when the tank reaches 70 mm before the automatic charge. A forced charge cancels the current charge, which can't be recovered, so if you're unsure, text us a photo of the tank and screen at (562) 609-4996.
Common questions
The printer says Check Ink Levels but the tank still looks fairly full. Should I refill?
Not yet. Epson says to keep printing until the ink is 70 mm (2.8 in) or less from the bottom of the tank, then refill a whole pack so it fits.
Can I split one ink pack between two tanks?
No. Pour the whole pack into one tank. Splitting packs throws off the printer's ink estimate.
How long is ink good once it's in the tank?
Epson's print quality guarantee is 25 days from refilling, or the date on the pack, whichever comes first.
What is a chip reservation?
After the firmware update, you can slide a new chip unit in before the current charge runs out. The printer uses it automatically when the charge is spent. You still pour in the ink only when the tank is down to 70 mm.
Refill Ink Tank appears but there's still more than 70 mm of ink. What does that mean?
Epson says the ink tank itself is due for replacement because its filter clogs over time. That's a service job, so contact us.
- Epson SureColor F7200 User's Guide (PDF)
- Epson SC-F7200 Series User's Guide CMP0048-03 (PDF)
- Epson SC-F7200 supplement: Charge and Reservation firmware notes CMP0091-01
- AA support requests about Epson sublimation ink chips not being recognized, 2024 to 2026











































































