Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
eufyMake E1 automatic cleaning, moisturizing modes, safe shutdown and storage
Keep the E1 plugged in and on: it flash-cleans every 10 minutes while idle and moisturizes the print head when it sits unused. After moisturizing, tap Inject Ink on the device page before you print. For a long break, use Storage mode or hold the power button for 5 seconds and wait for the shutdown sound before unplugging. Never just pull the plug.
What the E1 does on its own
As long as it has power, the E1 protects its print head without you doing anything:
- Flash clean: every 10 minutes while idle, takes about 5 seconds.
- Priming before a print: about 2.5 minutes, when it has been more than 12 hours since the last priming or cleaning, on the first job after a restart or update, and when you resume a paused job.
- White ink recovery: before a print, if you've used less than 3 ml of white in the last 36 hours. It stops settled white from printing faded. It's on by default and can be skipped on the Print Preparation page, but eufyMake recommends leaving it on.
- Auto deep cleaning: runs at your scheduled time if there has been no deep clean or moisturizing in 72 hours. Afterward you'll need to inject ink before printing.
Pick a moisturizing mode
Go to Printer Settings > Maintenance > Moisturizing mode. The default maintenance time is 2:00, and you can change it there.
| Mode | Best for | What happens |
|---|---|---|
| Auto | Printing daily or weekly | After 24 hours with no printing, it moisturizes once at your set time. |
| Flexible | Irregular schedules | After 24 idle hours it asks if you'll print in the next 48 hours. If yes, it skips moisturizing and runs extra flash cleans instead, then moisturizes at 72 hours anyway. |
| Storage | Trips, moves, long breaks | Moisturizes right away (about 7.5 minutes), then pauses all routine maintenance. |
Getting back to printing after moisturizing
-
Open the device page
In the app or Studio, open the device status home page.
-
Tap Inject Ink
Wait for it to finish, about 9 minutes after an automatic moisturizing cycle. The printer is then ready.
Choosing a manual cleaning level
Run these from the device page when prints show problems. Start low and only step up if the test print still isn't clean.
| Level | Use it for | Time |
|---|---|---|
| Cleaning | Small color shifts or unsteady ink output. eufyMake's troubleshooting pages also call this Medium Clean. | 2.5 min |
| Enhanced Cleaning | The same, when standard didn't fix it | 3 min 20 s |
| Deep Cleaning | Mild to moderate clogs or obvious defects. Ink is injected again automatically. | 9 min |
| Enhanced Deep | Severe clogs, a long idle period, or lines that keep dropping out | 40 min |
After any cleaning, run Test Printing from the Print Head Maintenance panel to check the result.
Safe shutdown
Before you start, make sure all ink cartridges and the cleaning cartridge are installed. If the cleaning cartridge has expired, the shutdown can't finish, so replace it first.
-
Hold the power button for 5 seconds
The button is beside the power connector. A sound confirms the shutdown has started.
-
Wait for it to finish
It moisturizes the head (about 7.5 minutes), parks it in the ink station and locks it. The whole process usually takes 8 to 10 minutes.
-
Unplug only after the finish sound
The power light turns red, the other lights go off, and the app shows Offline. If the power light stays green, check the app for an error, fix it and hold the button again.
eufyMake warns that unplugging without the shutdown process can permanently clog the head, and that this damage may not be covered by warranty.
Storing or moving it
- Store it in the original box, somewhere dry, dust-free and out of sunlight, at 41 to 95°F (5 to 35°C).
- Even in storage, eufyMake recommends printing at least once a month.
- Room to room: no need to remove the cartridges.
- By vehicle or shipping: shut down properly, remove all six ink cartridges and then the cleaning cartridge, cap or wrap the three connectors in the cleaning cartridge slot, check the head is locked on the ink station, cover the cartridge slots, and pack the platforms separately. Bag opened cartridges in their sealed bags.
- After a move, run a test print. eufyMake also recommends recalibrating the camera.
To turn it back on, plug it in and press the power button for about 1 second. It's ready in about 30 seconds. If something doesn't look right, text us at (562) 609-4996.
Watch eufyMake's video: factory reset and entering maintenance mode
More videos
Embedded from the manufacturer's official channel.
Common questions
Why does my E1 use ink when I'm not printing?
That's the automatic maintenance that keeps the head from clogging. The flash clean every 10 minutes uses a tiny amount. Priming before a print uses about 0.2 ml per color, and moisturizing and deep cleaning use cleaning fluid from the cleaning cartridge.
Why can't I print right after it moisturized?
The head is sitting in moisturizing fluid. Tap Inject Ink on the device page and wait about 9 minutes for it to finish.
Should I turn the printer off at night?
No. If you print daily or weekly, leave it on so maintenance can run. Only shut down for long breaks, using the 5 second power button hold.
Can I unplug it for a few minutes to move it?
eufyMake says a short unplug of about half an hour to an hour, for troubleshooting or moving it across the room, won't hurt the head. Plug it back in as soon as you can.
How do I get out of Storage mode?
There's no end button. Power it on, tap Inject Ink on the device page, and when that finishes it goes back to the mode you used before.











































































