Support
Machine type
Brand
eufyMake E1 UV Printer

eufyMake E1 print problems: missing colors, faded white, blurry prints, ink not curing, and temperature errors

✓ Reviewed by Jason KimUpdated 3 min readFits: eufyMake UV Printer E1
Short answer

Most E1 print problems start with the ink or the room, not a broken part. For missing colors, check the ink is official and in date and the room is 59 to 95°F, then run Test Printing and clean the bad color, stepping up to Deep Cleaning. Faded white is usually settled ink, fixed by the white ink repair. Blurry prints come from drafts, an open door, an uneven item or a dirty mat. Temperature and humidity errors mean the room is outside 59 to 95°F or 20 to 85% humidity.

Match your symptom

What you see Most likely cause Go to
A color missing or broken lines Clog, cold room, old ink, or the head was unplugged without shutdown Missing colors
White looks thin or faded White ink has settled Faded white
Ink smears or wipes off Not fully cured Ink not curing
Blurry or doubled image Drafts, uneven item, dirty or weak mat Blurry prints
Error starting with 0xFD0111 Room temperature or humidity Error codes

Missing colors or broken lines

  1. Check the basics

    Make sure the ink is official eufyMake ink and within its date, and that the room is 59 to 95°F. Cold ink gets thick and won't fire properly. Think back: was the printer unplugged without the 5 second shutdown?

  2. Run Test Printing

    From the Print Head Maintenance panel. Print white and varnish tests on clear film or colored paper so you can see them.

  3. Clean only the bad color

    If a color is missing or badly broken, answer No and select that color. The printer runs a Cleaning (eufyMake also calls it Medium Clean) and prints a new pattern.

  4. Step up to Deep Cleaning

    If the pattern is still badly broken or blank, run Deep Cleaning from the device page, then test again. Repeat it once more if needed.

  5. Try a new cartridge

    If lines are still broken after two Deep Cleanings, swap in a new cartridge of that color.

If one color still won't print, or none print at all, stop and text us. Have the test print photo, the printer serial number and a short video of the Deep Cleaning ready.

Faded white

White ink settles when it isn't used much. The printer usually spots this and starts a white ink repair on its own; just follow the prompt. To start it yourself, open the maintenance section in the app or Studio and run the white ink settling repair, then print a test image. Run it a second time if white is still weak. If nozzles drop out afterward, run one Enhanced Cleaning.

Ink not curing

  1. Confirm it with a tissue

    Wearing gloves, wipe the print with a dry tissue. Color on the tissue means curing is incomplete.

  2. If it happened right after setup, moisturizing or a deep clean

    Leftover fluid in the head may be mixing with the ink. Run Cleaning 3 to 5 times, then reprint.

  3. If you've been printing normally

    The UV lamp may be dirty. Clean the lamp surface as in the monthly cleaning, reprint and check again.

If curing is still poor, text us a photo of the print. eufyMake's next checks involve the lamp and the ink station, so we'll guide you through them.

Blurry or ghosted prints

  • Choose the correct substrate type in the software, and test with the White then CMYK ink mode.
  • Keep the door closed and switch off any fan blowing on the printer. Moving air pushes the ink drops off course.
  • Remove any bits stuck to the adhesive mat. They throw off the height reading.
  • Keep the item within 2 mm of flat. For a test, stick a flat sheet of paper or film to the mat.
  • If you fitted a new flatbed, run camera calibration with white paper on its mat.
  • If the item shifts during printing, the mat has lost its grip. Replace it.

Error codes

Code Meaning What to do
0xFD0111000D Room temperature or humidity out of range Bring the room to 59 to 95°F and 20 to 85% humidity, wait more than 3 hours, try again
0xFD01110005 Too cold to print Leave the printer and ink powered on in a warm room for 12 hours
0xFD01110001 to 0003 Printer can't read its temperature sensor Text us. The fix is inside the case
0xFD01120002, 0006 to 0009 Laser sensor blocked Clear anything blocking the laser openings at the left and right vents

Still stuck? Text a photo or short video to (562) 609-4996. It helps to upload the printer logs from the app or Studio first.

Watch eufyMake's video: how to check whether ink curing is sufficient

More videos

eufyMake: low temperature troubleshooting
eufyMake: printed material scraping the print head
eufyMake: laser sensor troubleshooting
eufyMake: E1 deep maintenance

Embedded from the manufacturer's official channel.

Common questions

Why can't I see white or varnish on my test print?

Both are hard to see on white paper. Print the test on clear film or colored paper.

How do I know if a print is fully cured?

Wearing gloves, wipe it gently with a dry tissue. Color coming off on the tissue means it isn't fully cured. Scratching it with something hard is not a fair test.

Ink peels off metal, acrylic or glass. What should I do?

These surfaces need a primer. Wipe on the matching UV adhesion promoter pad in one direction (one pad covers about a letter-size sheet), let it stand for about 10 minutes, then print. Wear gloves and a mask.

The printer won't start a job and shows a temperature or humidity error. Is it broken?

Not necessarily. If the room is outside 59 to 95°F or 20 to 85% humidity, or close to those limits, the E1 blocks printing on purpose. Bring the room into range and give it more than 3 hours to settle.

My print has dark scrape marks on it. What happened?

The item touched the print head, usually because it lifted or moved on the mat, the mat itself is warped or worn, or thin acrylic bulged under the UV light. Press the item and mat flat and replace a mat that won't hold. For flexible items use soft white ink. On acrylic thinner than 5 mm, print flat 2D designs only, not raised textures.

Did this fix it?