Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
eufyMake E1 monthly cleaning and replacing the cleaning cartridge, air filter, ink pad and scraper
Once a month, wipe the UV lamp, the area around the print head, the flatbed and the print head station with ink cleaning solution on a lint-free swab, wearing gloves. Every 3 months add the camera cover and a little oil on the guide rods. Replace the air filter, ink pad and scraper about every 6 months or when the app reminds you, and the cleaning cartridge when it reports full.
UV ink and the cleaning solution are mildly corrosive. Wear nitrile gloves and eye protection, don't let solution drip onto the outside of the printer, and never touch the encoder strip (the thin strip along the print head's path). Touching it causes calibration errors.
What you need
Lint-free cloths, lint-free swabs, ink cleaning solution, nitrile gloves, a silicone ink scraper and, for the quarterly clean, anti-rust lubricating oil. The eufyMake E1 maintenance kit has all of these.
Monthly cleaning
-
Make room to work
With the printer idle, use the app to move the print head out along its rail toward the camera, and move the platform base forward as far as it goes.
-
Clean the UV lamp
Wipe the whole lamp surface with a swab dampened with cleaning solution until no ink is left, then dry it with a clean cloth.
-
Clean around the print head
Wipe away ink splatter around the print head with a damp swab and dry it. Don't use cleaning solution on the nozzle area itself.
-
Clean the flatbed base
Wipe it with a cloth dampened with cleaning solution, then wipe it dry.
-
Clean the print head station
Clean the scraper blade and the ink pad with a damp swab until no ink residue remains.
Every 3 months
Do everything above, plus:
- Camera cover: wipe the protective cover over the camera with a damp swab, then dry it.
- X-axis rail: if there's dust or oily buildup, wipe with a dry cloth only. No cleaning solution on the rail.
- Guide rods: put a little anti-rust oil on a swab and apply it to the X-axis rail, the two Y-axis rods and the four Z-axis rods. Turn the standard flatbed over, oil its two rods and slide the plate back and forth to spread it.
Replacement schedule
| Part | When | Reminder? |
|---|---|---|
| Cleaning cartridge | When it reports full or expired | Yes |
| Air filter | About every 6 months, or when odors get stronger | Yes |
| Ink pad and scraper | About every 6 months, or drips and unstable colors | Yes |
| Foam pads | Check every 6 months, replace when nearly saturated | No |
| Adhesive mat | When it stops holding or is damaged | No |
Replace the cleaning cartridge
-
Remove the cover
Pull the cover on the right side of the printer outward.
-
Pull out the old cartridge
It's a snug fit with no screws. Hold the top and bottom and pull gently. Wrap it up if it has leaked.
-
Fit the new one
Keep it upright and line its connectors up with the posts inside, then press it in until it sits flat against the inner wall. Don't touch the chip.
-
Check it
Run a cleaning cycle to confirm the printer sees the new cartridge.
Replace an ink cartridge
Wait until the printer is idle. Press down on the empty cartridge so it pops up, lift it out and set it upside down so it doesn't drip. Insert the new one straight and level in the slot with the matching letter, press it level with the others, and wait 2 to 5 seconds for its light to turn green.
Replace the air filter
Open the air filter compartment cover, pull out the old filter, push in the new one the right way round, and close the cover. Keep the room ventilated even with a fresh filter.
Replace the ink pad, scraper and foam pads
eufyMake recommends doing the ink pad and scraper together, using the Print Head Station Replacement Kit, which includes gloves and tweezers.
-
Move the head and power off
Lift off the top cover by pressing both sides at the bottom. With the printer idle, use the app to move the print head out of the ink station, then turn the power off and slide the head further out by hand.
-
Swap the ink pad
Squeeze its two clips and lift it out. If the rubber plug comes out, put it back flanged side out. Press the new pad down until it clicks.
-
Swap the scraper
Swing the scraper up to vertical, squeeze its two clips and remove it. Line the raised part of the new one up with the slot and press until it clicks.
-
Swap the foam pads
Remove a cartridge, lift the old pad out of the slot with the tweezers, and press a new one flat. Only ever one layer, or the cartridge won't come out.
-
Power on and reset
Check everything is seated, reconnect power, and reset the scraper maintenance cycle in the app or Studio.
If anything doesn't seat or the app keeps showing a warning, text us a photo at (562) 609-4996.
Watch eufyMake's video: E1 routine maintenance
More videos
Embedded from the manufacturer's official channel.
Common questions
Can I clean the print head nozzles with cleaning solution?
eufyMake doesn't recommend it. Clean around the print head, not the nozzle surface itself, and let the printer's own cleaning cycles look after the nozzles.
Can I keep printing after the cleaning cartridge says it's full?
No. It keeps just enough room for one last moisturizing cycle to protect the head. Replace it before printing again.
How do I clean a dusty adhesive mat?
Rinse it gently with clean water and let it dry completely. Don't use alcohol on the sticky side. Replace it when it no longer holds items, or is torn, curled or stained with ink.
Do I need the official cartridges?
Yes. eufyMake says the E1 only works with its own ink and cleaning cartridges. Third-party cartridges are not supported.
Which parts does the app remind me about?
The print head, cleaning cartridge, air filter and scraper. The adhesive mat and foam pads have no reminder, so check them yourself.
- Manually Cleaning (routine monthly cleaning)
- Manually Deep Cleaning for UV Printer E1
- E1 Maintenance Accessories Guide
- Introduction to Print Head Station Replacement Kit and Replacement SOP
- How to Replace the Cleaning Cartridge
- Introduction to Cleaning Cartridge
- How to Replace Ink
- Component lifespan reminder instructions











































































