Support
Machine type
Brand
eufyMake E1 UV Printer

eufyMake E1 setup: cartridges, binding, initialization and your first print

✓ Reviewed by Jason KimUpdated 3 min readFits: eufyMake UV Printer E1
Short answer

Plug in the E1 (it turns on by itself), install the six ink cartridges, the cleaning cartridge with its rubber plugs removed, and the air filter. Then open the eufyMake app or Studio, bind the printer to your account, and let initialization run: it checks the printer, fills the ink lines (about 27 minutes), prints a test pattern and calibrates the camera. You only do this once, or again after a factory reset.

Before you unbox

Pick the spot first. The E1 weighs about 15 kg empty and up to 25 kg with ink and accessories. It needs a flat, solid surface, 59 to 95°F and 20 to 85% humidity, at least 16 inches clear in front and behind so the door opens fully, 12 inches on the right side for the cartridges, and a gap from the wall on both sides. Check that the power supply and plug match your outlet.

Install the hardware

  1. Connect the power

    Plug in the adapter and power cord. The E1 turns on by itself as soon as it has power.

  2. Install the six ink cartridges

    Check each cartridge's expiry date and that the packaging isn't leaking. Match the letter on the cartridge to the slot (K, C, M, Y, W and G for varnish) and press it straight down until it sits level with the others. Each color has a keyed bottom, so if a cartridge doesn't slide in smoothly, stop. Forcing it can break the key. Don't touch the chip.

  3. Install the cleaning cartridge

    Pull off the cleaning cartridge cover on the right side by its handle. Pull out the rubber plugs inside the compartment first. The cartridge won't seat with them in. Slide the cartridge in the right way round, then snap the cover back on.

  4. Install the air filter

    Remove the magnetic front cover, push the air filter in, then put the cover back until it clicks.

Bind and initialize

  1. Install the software and sign in

    Install the eufyMake app on your phone (the easiest way to bind) and eufyMake Studio on your computer. From version 5.0 both are named Anker Make. One account signs in to all of them.

  2. Bind the printer

    The app walks you through it: choose the model, choose Wi-Fi or Ethernet, find the printer by Bluetooth or by scanning the QR code on the printer, authorize, set up Wi-Fi, done.

  3. Let initialization run

    It starts on its own after binding. The printer checks itself, fills the ink lines, prints a test pattern and calibrates the camera. The ink fill alone takes about 27 minutes and flushes out the protective fluid the print head ships with. Follow the prompts and don't interrupt it.

  4. Print your test pattern

    Use a clean, flat sheet of white paper or film on the adhesive mat. If lines are missing in a color, answer No and pick that color, and the printer cleans it and prints a new pattern.

  5. Calibrate the camera

    You can reuse the test paper. It must cover the whole platform and lie flat with no lifted edges. eufyMake recommends doing this on the mini flatbed. On the standard flatbed, remove the two foam fixing pads first, and keep 40 cm clear around the platform.

Keep the printer plugged in and on after setup. It runs its own cleaning and moisturizing in the background. Never shut it off by pulling the plug: eufyMake says print head damage from that may not be covered by warranty.

If a setup step fails

Step What to try
Test pattern Run Cleaning or Deep Cleaning until it prints cleanly. After three Cleanings and one Deep Cleaning, try a factory reset and initialize again.
Calibration Make sure the test pattern is clean first, and that black prints the four corner QR codes. Check the paper covers the platform and nothing blocks the camera on top.
Ink fill A new cartridge shows low ink: shake it for about 10 seconds and reinsert it. Try a spare of the same color if you have one.
Low temperature Leave the printer and ink powered on in a warm room for 12 hours, then try again.

After a factory reset, make sure every cartridge is at least half full before you initialize again. If a step still fails, text us a photo of the screen and the test pattern at (562) 609-4996 and we'll help you sort it out.

Watch eufyMake's video: E1 unboxing and installation

More videos

eufyMake: E1 setup and beginner's guide
eufyMake: the main E1 printing workflow
eufyMake: camera calibration failure solution
eufyMake: low temperature troubleshooting

Embedded from the manufacturer's official channel.

Common questions

Do I have to initialize the E1 every time I turn it on?

No. Initialization only runs the first time the printer starts, or after a factory reset. After that, keep the printer on and it looks after itself.

Can more than one person use the printer?

One account is the primary owner. That account can share the printer with up to 3 other users.

Should I set it up with Wi-Fi or a cable?

Either. Wi-Fi is easiest. An Ethernet cable to your router is more stable; your phone or computer then needs to be on the same network.

The test pattern has broken lines. Is the print head bad?

Usually not. Run Cleaning (eufyMake also calls it Medium Clean) or Deep Cleaning until the pattern prints cleanly. eufyMake suggests a factory reset and a fresh initialization only after three Medium Cleans and one Deep Clean haven't fixed it.

My printer arrived in cold weather and says Low Temperature. What do I do?

Leave the printer and ink in a warm room (59 to 95°F), powered on, for 12 hours before filling ink or printing. The inside of the printer takes longer to warm up than the room.

Did this fix it?