Support
Machine type
Brand
Epson SureColor F2270

Epson Garment Creator 2 basics for the F2270 and F3070: T-shirt types, ink density and sending a job

✓ Reviewed by Jason KimUpdated 3 min readFits: F2270 · F3070 · SC-F2200 Series · SC-F3000 Series
Short answer

In Garment Creator 2, pick your printer and T-Shirt or Film mode, choose the T-shirt type that matches the garment, then print the Ink Density chart on that same shirt and save the best values to your Presets. Place the image inside the light blue platen frame, set the number of prints and click Print. Don't run Garment Creator 2 and another RIP at the same time over USB.

Which printers use it

Garment Creator 2 is Epson's free print software for its DTG printers. Its operation guide covers the SC-F3000 Series (F3070), the SC-F2200 Series (F2270) and the SC-F1000 Series. If a printer doesn't support it, it won't appear in the printer list. The F2100 and F2000 use the original Garment Creator instead. On the F3070, Epson's earlier Garment Creator for SC-F3000 Series also works, and its saved work files open in Garment Creator 2.

If the printer is connected by USB, don't run Garment Creator 2 and another RIP at the same time. Epson says this can cause a Command Error or bad prints. Open only one.

Your first job, step by step

  1. Pick the printer and the job mode

    Click the printer area at the top of the screen and choose your printer from the list. On Windows, if it isn't listed, install the printer's communication driver first. Then choose T-Shirt or Film at the switch job creation mode buttons. Switching changes the white and color printing order and the layout, so pick it before you lay out the image.

  2. Choose the T-shirt type

    On the Print Settings tab, pick a type in Presets:

    • Light Color T-Shirt (Standard): color ink only, no white. The only type allowed when the printer is in Color ink mode.
    • Dark Color T-Shirt (Standard): an automatic white under-base under all colored areas, including black.
    • Black Color T-Shirt (Use Garment Black): leaves pure black (R,G,B 0,0,0) areas unprinted so the shirt shows through. Saves ink. Only works when the art was made in RGB with the sRGB color space.
    • Dark Color T-Shirt (White): white ink only.
    • Light Color T-Shirt (High Speed Color mode): F2270 only, and only when the printer is set up in High speed color mode.
  3. Dial in ink density on a test shirt

    Before a real run, click Print Chart under Ink Density, then load the same kind of shirt you'll print, pre-treated (for white) and on the platen you'll use, and press the start button on the printer. Cure the chart, pick the best block and type its values into Color Density, White (Top) and White (Base) as the chart shows. Then register the result in your Presets, or it's lost when you close the software. Redo it for each new fabric or shirt brand.

  4. Place the image

    Click Open or drag the file in. The light blue frame is the platen and the printable area. On Layout Settings, choose the platen size you're using, then drag, type exact positions, use Top-Center, or Fit to platen. Size changes keep the aspect ratio. Save a layout you reuse to Presets.

  5. Send it

    Set the number of prints and click Print. When the printer has the job, its screen shows a preview and the start button lights. Load the shirt and press it.

If the Print button is greyed out

  • The printer is off, in an error, or still busy (for example cleaning). Wait for the status icon to stop spinning, clear any error, and try again.
  • The T-shirt type doesn't match the printer's mode. A printer in Color ink mode won't accept Dark Color or Black Color jobs.

Settings worth knowing

  • Print Quality: slide toward Quality for better results at lower speed. Epson recommends the highest level for white on polyester.
  • Print Direction: Bi-Direction (High Speed) is normal. Uni-Direction (Low Speed) can fix misaligned lines on shirts that soak up ink.
  • Reduce White Area: pulls the automatic under-base in if it shows past the edges of the design.
  • White: No Print: drops the white background from art that has one. It also drops any white inside the design, so use Color Replacement with Transparent for backgrounds instead.
  • Double Strike Print (F3070): clear it if the under-base and colors blur, so the base prints and dries first.

Image files that work best

TIFF, JPEG, PNG (8 bit) or BMP, up to 2 GB and 10 million pixels. Epson recommends RGB, sRGB and 300 dpi. Work files save as .gcr and only open for the same printer model.

Need help setting it up? Text us at (562) 609-4996.

Epson's video: DTG print settings in Garment Creator 2

More videos

Epson: loading an image into Garment Creator 2
Epson: DTFilm print settings in Garment Creator 2 for the F2270
Epson: making print-ready USB files in Garment Creator 2
Epson: using the Garment Creator 2 cost estimator

Embedded from the manufacturer's official channel.

Common questions

Does Garment Creator 2 work with the F2100?

Epson's Garment Creator 2 guide covers the SC-F3000, SC-F2200 and SC-F1000 Series. The F2100 and F2000 use the original Garment Creator.

Why is the Print button greyed out?

Either the printer isn't ready (off, busy or in an error), or the T-shirt type needs white ink and the printer is in Color ink mode.

Which T-shirt type saves the most ink on black shirts?

Black Color T-Shirt (Use Garment Black). It leaves pure black areas unprinted so the shirt color shows through. The art must be RGB and sRGB for it to work.

Do my ink density settings save automatically?

No. They last until you close the software. Register them in your Presets to reuse them.

What resolution should my art be?

Epson's Garment Creator 2 guide recommends 300 dpi, RGB and sRGB.

Did this fix it?