Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
GFP laminator loading and threading film: 200 Series, 300 Series and 563TH
Load the film roll so liner-in film unwinds from the bottom and liner-out from the top, center it with the shaft numbers and line the bottom roll up with it. On 200 and 300 Series machines, lead the film through on a leader board and tape the liner to a cardboard core on the rewind shaft; on the 563TH, pass the film through the rollers, split the liner with the film cutter and bring the media up from the feed tray. The film should run wrinkle-free and tight on the roller.
Most bad laminations start with a badly loaded roll. GFP's method is the same idea on every series: load both rolls lined up with each other, lead the film through with a board, and take the liner up on a cardboard core. The details differ slightly between the 200 and 300 Series and the 563TH, so follow the section for your machine.
Load the rolls (all series)
-
Open the shafts
Rotate the locking outer sleeves on the supply shafts to the open position, lined up with the inner sleeve. On the 563TH the top supply shaft swings out to load.
-
Check which way the film unwinds
Liner-in film comes off the bottom of the roll. Liner-out film comes off the top.
-
Center and match the rolls
Slide the film roll on and center it using the numbers on the shaft (on the 200 Series, measure the gap from the roll to the side frame). Load the bottom roll in the same position so the two line up. On the 200 Series, the bottom shaft's brake assembly slides off one end so the roll can go on.
-
Lock and set the brakes
Lock the sleeves, then add just enough brake tension that the web will not sag. The roll must still turn.
-
Fit the liner core
Slide an empty cardboard tube onto the liner rewind shaft.
Thread the film: 200 and 300 Series
-
Open the rollers
Turn the hand wheel counterclockwise to raise the top roller.
-
Lead with a board
Pass the film under the idler bar and down in front of the roller. Peel back about 1 in of liner, stick the film to a leader board as wide as the roll, and push the board into the rollers.
-
Close and attach the liner
Lower the top roller onto the board. Take the liner up behind the pressure linkage shaft and tape it to the cardboard tube on the rewind shaft.
-
Bring up the bottom web
Use the foot pedal to advance until the board is under the roller. Pull the media or kraft paper up and stick it to the exposed adhesive, then pedal both webs through until they clear the nip.
Thread the film: 563TH
-
Through the rollers
Pull the film web under the rewind shaft with some resistance on the brake, raise the top roller, pass the film between the rollers and lay it on the rear table. Pull it flat and lower the roller.
-
Split the liner
Separate enough liner to tape to the tube on the top rewind shaft. Use the film cutter between liner and film so you only cut the liner, and keep the blade off the heat roller.
-
Expose the adhesive and add the media
Pedal until adhesive shows on the front of the heat roller. Raise the feed tray, bring printed media up behind the idler bar (mounting adhesive goes in front of it), lower the tray and pedal both webs through the nip.
Never cut film on the rubber rollers, and keep knives and rulers off the working tables. Rubber roller damage shows up in every print after it.
Check before you run
The film should lie wrinkle-free and tight against the roller. If it is not tight, add a little nip pressure. Wrinkles in the film web: adjust the top supply brake. Wrinkles in the bottom web: adjust the bottom brake. Our GFP pressure and tension guide covers both. Still fighting it? Text us a photo of your threading at (562) 609-4996.
Watch GFP's video: webbing film through the machine
More videos
Embedded from the manufacturer's official channel.
Common questions
Which way should the film come off the roll?
Liner-in film comes off the bottom of the roll, liner-out film off the top.
What is a leader board?
A stiff board as wide as the film roll that you stick the film to, so it leads the web through the rollers.
How tight should the brakes be?
Only enough to take wrinkles out of the web before it reaches the rollers. The roll must still turn freely.
Mounting adhesive on a 563TH: front or behind the idler bar?
In front of it. Printed media goes behind it.











































































