Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
GFP laminator troubleshooting: wrinkles, curl, cloudy laminate, rollers not turning and no heat
On GFP laminators, wrinkles on both webs mean too much nip pressure, cloudy laminate means too little pressure or a dusty print, and curl means too much brake tension on the top roll (curl up) or bottom roll (curl down). If the rollers will not turn, release the emergency stop and ease off the nip. A photo-eye stop is cleared by flipping the operation switch to Foot or Step and back.
GFP's manuals list the same handful of problems for the 200, 300 and 500 Series. Here they are in one place, with the fix that GFP gives. Most are tension or pressure, not a broken machine.
Match your symptom
| Problem | Likely cause | Fix |
|---|---|---|
| Won't turn on | Unplugged, switch off, breaker tripped, fuse | See "Won't power up" |
| Rollers won't turn on Run | E-stop pressed, or too much nip | Release the e-stop; reduce nip |
| Stops by itself | Photo-electric eye tripped | See "Stopped by the photo eye" |
| Cloudy or poor adhesion | Nip too low, or dust on the print | More nip; clean the print first |
| Poor adhesion on one side | Uneven roller gap | Paper test, then contact us |
| Curls up | Too much top roll tension | Reduce top brake |
| Curls down | Too much bottom roll tension | Reduce bottom brake |
| Wrinkles top and bottom | Too much nip pressure | Back off the hand wheel |
| Film roll goes slack | Too little supply brake | Add brake on that roll |
| Liner goes loose on rewind | Too little rewind tension | Add rewind tension |
| Top roller not heating | Heater not switched on or set | See "Heat" |
Won't power up
-
Basics
Check the cord is plugged into a working grounded outlet and the rear power switch is on.
-
Breaker
Reset the building circuit breaker if it has tripped.
-
Fuse
With the machine unplugged, check the fuse on the rear panel and replace it with the same rating. The 200 Series uses a 1 amp 5 x 20 mm fuse; the 563TH packing list includes a 2 A 5 x 20 mm fuse. If a new fuse blows again straight away, stop and contact us.
If it still will not run, GFP lists a failed motor as the remaining cause. That is a technician repair: GFP warns owners not to service or repair the laminator themselves.
Stopped by the photo eye
The safety eye stops the rollers when something comes too close. To restart, flip the operation switch to Foot (on the 563TH, Step) and back to Run (Continuous on the 563TH). Clear whatever tripped it first.
Heat (300 Series and 563TH)
- Set the heater switch to Hot and turn the temperature control up. For cold laminating, set it to Cold.
- 300 Series: the Hot light flashes while warming and stays on when ready. GFP suggests setting 4 as a starting point for most vinyl.
- 563TH: the green Ready light comes on at temperature, and the screen shows the actual roller surface temperature. The screen does not work in Cold mode; that is normal.
- Too much heat hurts quality. Match the temperature to the film.
Adhesive on the rollers
Film adhesive is hard to get off rubber. Prevent it by always running a sled, kraft paper or media at least as wide as the film. If it happens, clean it off the same day with a rubber eraser, or isopropyl alcohol on a shop towel, with the power off and the rollers cool. Never use flammable sprays, and never cut on the rollers.
Something not on this list, or a noise or burning smell? Stop the machine and text us a photo or video at (562) 609-4996.
Watch GFP's video: nip adjustment on the 500, 300 and 200 Series
More videos
Embedded from the manufacturer's official channel.
Common questions
Why won't the rollers turn when I press Run?
GFP lists two causes: the emergency stop is engaged, or the nip pressure is too high.
The laminate looks cloudy.
Increase nip pressure a little, and make sure the print is dust-free before laminating.
The 563TH screen is blank.
The temperature screen does not work in Cold mode. Switch to Hot to see it.
Can I clean the rollers with solvent spray?
No. GFP says no flammable sprays. Use a rubber eraser or isopropyl alcohol on a shop towel.











































































