Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
GFP laminator jobs: laminating sheets on a sled, kraft paper, roll to roll, and mounting to boards
On a GFP laminator, laminate single sheets on a sled as wide as the film, batches of sheets on a kraft paper roll unwinding from the bottom, and printed rolls unwinding from the top. To mount, pre-coat boards with mounting adhesive using a leader board of the same thickness, then press prints onto them while holding back the liner. Always keep a carrier under the film so adhesive never reaches the bottom roller.
GFP describes five everyday jobs for these laminators. Which one you use depends on whether your prints are loose sheets or a roll, and whether you are overlaminating or mounting. The one rule that runs through all of them: adhesive must never touch the bare bottom roller.
Always run a bottom web, sled or board at least as wide as the film. If your sheets are narrower than the film, use a laminating sled or a kraft paper roll underneath. Film adhesive is very hard to get off the rubber.
Single sheets on a sled
-
Set the gap to the sled
Load the film on top. Raise the top roller, slide a sled (a Gatorboard or PVC mounting board as wide as the film) into the nip, lower the roller until it touches the sled, then reverse the sled back out with the foot pedal.
-
Lead the film
Thread the film under the idler bar, stick it to a leader board, and pedal it halfway through the rollers.
-
Run the print
Lay the print on the sled and run it through with the foot pedal. Put the next sled or a leader board right behind it so the adhesive never lands on the bottom roller.
Many sheets on kraft paper
Load film on top and a kraft paper roll on the bottom front supply shaft, unwinding from the bottom of the roll. Thread both webs, press Run, and feed sheets one after another.
Roll to roll
Load film on top and your printed roll on the bottom front supply shaft, unwinding from the top of the roll. Thread both and press Run. Center and match both rolls so the edges line up.
Pre-coating mounting boards
-
Set up
Load mounting adhesive on top. Put a leader board as thick as the boards you will coat into the nip and lower the roller until it touches.
-
Run boards
Stick the adhesive to the leader board and run it halfway through. Feed the boards one after another on the foot pedal.
-
Finish with a board
After the last board, run another leader board through so adhesive cannot reach the rollers.
Mounting a print to a pre-coated board
-
Start the edge
Peel back and fold down about 1 in of liner on the coated board. Stick the leading edge of the print to the exposed adhesive.
-
Into the nip
Push the first inch of the board into the rollers and lower the top roller. Lay the print back over the top roller.
-
Run it
Hold the release liner with one hand, keep light pressure on the print as it comes over the roller, and run the board through on the foot pedal.
Good to know
- Under 1/2 in thick runs continuously. From 1/2 in up to 1 in, use the foot pedal. Never run metal or other hard objects.
- Top heat models: switch to Hot and let it reach temperature before running. On the 300 Series, GFP suggests setting 4 as a start for most vinyl. For cold film, use Cold.
- Dust trapped under the laminate shows. Clean prints before you run them, and keep the room clean.
Not sure which film or mounting adhesive suits a job? Ask us: (562) 609-4996.
Watch GFP's video: 200 Series cut sheets with a carrier
More videos
Embedded from the manufacturer's official channel.
Common questions
What can I use as a sled?
GFP suggests a piece of Gatorboard or other PVC mounting board as wide as the film web.
Which way does kraft paper unwind?
From the bottom of the roll. A printed media roll unwinds from the top.
How thick can a board be?
Up to 1/2 in runs continuously; between 1/2 in and 1 in, use the foot pedal.
Why run a leader board after the last mounting board?
So the exposed adhesive does not contact the rollers.










































































