Support
Machine type
Brand
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses

Insta 718, 728 and 828 maintenance: cleaning the platen, monthly grease, air filter care and replacing the silicone pad

✓ Reviewed by Jason KimUpdated 2 min readFits: Insta 718 · 728 · 828
Short answer

Wipe the coated heat platen with a soft, non-abrasive cloth and use mineral spirits only on a cold press. Grease the post and the heat platen pivot pin with high-temperature, non-melting grease about once a month if the press runs all day. Turn the air off when you're done, keep the clear filter bowl away from solvents and sunlight, and keep zippers, snaps and buttons off the platen.

Insta calls these presses relatively maintenance free, and that holds if you do a few small things on a schedule. Everything below comes from Insta's maintenance section for the 718, 728 and 828.

Match your symptom

What you see Likely cause Go to
Residue or stains on prints Dirty platen or dirty press body Cleaning
Lines, scratches or grooves showing on prints Damaged platen coating Protect the platen
Swing feels stiff or squeaks Post and pivot pin need grease Grease
Pad torn, cut or lifting Pad worn out Replace the pad

Cleaning

  • Wipe the coated heat platen regularly with a soft, non-abrasive cloth.
  • For stubborn stains, wait until the platen is cold, then use mineral spirits.
  • Wipe the outside of the press and both platens with a clean rag now and then, so dust and grime don't end up on garments.
  • Mineral spirits are flammable. Never use them on a hot press or near a spark or flame.

Protect the platen

Don't press buttons, pins, snaps or zippers directly. They cut the silicone pad and scratch the coating on the heat platen. Use a pressing pillow or cover sheet to lift those areas off the platen. When the press is hot and not in use, keep the heat platen swung open, away from the pad.

If a new press shows lines or grooves in the heat platen that print onto garments, don't try to sand or polish it. Take photos, note the serial number, and contact us.

Grease

  1. Let it cool and turn it off

    Disconnect power before any servicing or cleaning.

  2. Grease the post and the pivot pin

    Use a high-temperature, non-melting grease (Insta part MPPL023, with grease gun MAPG010). Insta points to the post and the heat platen's pivot pin. The parts list also shows a grease fitting on the press.

  3. Wipe off the excess

    Excess grease attracts lint and can transfer to garments.

How often depends on use. Insta's guide is about once a month for a press that runs continuously.

Air system care

  • Turn off the air supply when the press isn't being used.
  • Keep the clear filter bowl and the pressure gauge out of direct sunlight, away from knocks, and within their rated temperature.
  • Don't clean the bowl with detergents or solvents, and don't use it on air systems where the compressor runs fire-resistant lubricants such as phosphate esters.
  • Keep the work area clean and uncluttered.

Replace the silicone pad

  1. Start cool and clean

    Make sure the platens are cool. Clean the metal surface with a mild solvent such as mineral spirits, and let the pad and the metal dry completely.

  2. Spread the adhesive

    Use Insta's silicone adhesive sealant (MPPC006) and read the tube's instructions. Spread a thin, even coat on the metal platen. A notched spreader like the ones used for floor tile helps.

  3. Lay the pad

    Apply the pad right away. Press it down and position it so no air is trapped underneath.

  4. Let it cure

    Leave it overnight under light pressure at room temperature.

Insta's manual also covers adjusting the swing-arm micro switch with power on and the cover removed. That is a technician job because the terminals are live. Contact us instead.

Common questions

How often should I grease an Insta 728?

Insta says it depends on use, about once a month if the press runs continuously. Grease the post and the heat platen pivot pin and wipe off any excess.

What grease do I use?

A high-temperature, non-melting grease. Insta's part is MPPL023, applied with its grease gun MAPG010.

My new press has lines or grooves on the heat platen that show on prints. What do I do?

Don't sand or scrape the coating. Take clear photos and the serial number and text us at (562) 609-4996 so we can work it out with Insta.

What can I clean the clear air filter bowl with?

Not detergents or solvents. Insta warns against detergents, chlorinated hydrocarbons, ketones, esters and some alcohols on the polycarbonate bowl. Wipe it with a clean dry cloth.

Can I replace the silicone pad myself?

Yes. Insta publishes the procedure. It uses its silicone adhesive (MPPC006) and needs to cure overnight.

Sources
Did this fix it?