Support
Machine type
Brand
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses

Insta 718, 728 and 828 setup: power, air pressure, two-hand start and your first press

✓ Reviewed by Jason KimUpdated 2 min readFits: Insta 718 · 728 · 828
Short answer

Put the press on a level, non-flammable bench that holds 300 lbs, plug it into its own circuit (15 A for the 718 and 728, 20 A at 230/240 V for the 828), and feed it 30 to 100 psi of air. Turn it on, set temperature and time, swing the heat platen over the lower platen, and hold both green start buttons until the platens touch. The press then times the cycle and opens by itself.

The 718, 728 and 828 all set up the same way. The only real differences are platen size and power: the 718 and 728 are 120 V presses, and the 828 in the US is a 230/240 V press. Follow these steps the first time, and keep the Insta manual with the machine.

Before you plug in

  • Bench: even, non-flammable and able to carry at least 300 lbs. The 718 weighs 128 lbs, the 728 143 lbs and the 828 218 lbs.
  • Outlet: the base of the press should sit above the wall socket, and nothing should block the main power switch.
  • Circuit: a separate 15 A circuit for the 718 and 728. A separate 230/240 V 20 A circuit for the US 828. Keep line voltage within 10% of the rating and avoid voltage spikes.
  • Extension cords: only heavy industrial cords, 16/3 up to 25 ft or 14/3 up to 50 ft.
  • Liquids: keep drinks, sprays and pretreat bottles away from the press.

If the power cord is ever damaged, don't repair or swap it yourself. Insta says the cord must come from the manufacturer. Contact us.

Connect air

The press closes with air, so it needs a compressor or shop air line. The regulator and gauge are on the front of the base. Insta's operating range is 30 to 100 psi, and the input must never go over 100 psi. US machines ship with a standard air fitting.

  • Keep your hands clean when you touch the clear air filter bowl, and don't put synthetic grease on it.
  • The filter bowl may feel slightly loose out of the box. Insta leaves it that way so it doesn't crack in shipping.
  • Turn the air off at the end of the day.

Your first press

  1. Turn it on

    Press POWER/MODE on the controller. (Hold it for 3 seconds later to turn the controller off.)

  2. Set temperature and time

    Press POWER/MODE until temperature shows, then hold SET and press the up or down arrow. Do the same with the timer display. If you use presets, press PGM to pick one. See the controller guide for details.

  3. Let it heat

    Swing the heat platen all the way open, away from the lower platen, and wait until it reaches your set temperature.

  4. Set pressure

    Turn the air regulator on the front of the base until the gauge shows the pressure you want, within 30 to 100 psi. Fine-tune it after a test print.

  5. Load the garment

    Lay the garment on the lower platen and smooth out every wrinkle. Position the transfer.

  6. Swing the heat platen over

    Use the swing-away handle to bring the heat platen fully into place over the lower platen.

  7. Hold both start buttons

    Press and hold both green buttons together until the lower platen meets the heat platen. Then let go. The press seals for the set time and opens itself at the end.

  8. Swing away and unload

    Swing the heat platen to the other side and take the garment off.

Only one person should run the press. Keep hands clear of both platens, don't touch the heat platen or the aluminum arm, and don't handle the press with wet hands.

If the first press doesn't close

Check that the heat platen is swung fully into position, that the gauge shows air, and that you held both buttons until the platens touched. Insta's controller also has a short safety delay that is on by default, so hold both buttons for at least a second. If it still won't close, see the troubleshooting guide or text us a short video at (562) 609-4996.

Watch Insta's video: how to load a t-shirt onto the Insta 728

More videos

Meet the Insta 728 heat press

Embedded from the manufacturer's official channel.

Common questions

How much air pressure does an Insta 728 need?

Insta lists an operating range of 30 to 100 psi. Never feed it more than 100 psi; Insta warns that running above that can damage the machine.

Why do I have to hold both buttons?

It keeps both hands away from the platens while the press closes. Hold both until the platens touch, then let go. The cycle continues on its own.

How do I stop a press in the middle of a cycle?

Push the DISENGAGE button in the center of the panel. The cycle stops right away and the timer resets.

How do I turn the controller off?

Hold POWER/MODE for 3 seconds.

Can I run an 828 on a normal wall outlet?

No. The US 828 is a 230/240 V press that needs its own 20 A circuit. The 718 and 728 run on 120 V with their own 15 A circuit.

Sources
Did this fix it?