Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Insta 907 won't press, won't close, opens right away or won't heat
The 907 only cycles when the heated arm sits directly over one of the two lower platens and both start buttons are held until the platens meet. Also check that the gauge shows 30 to 100 psi, the timer isn't at zero, and DISENGAGE wasn't pressed. If it won't heat, wake it from sleep and check its circuit. Don't open the control housing.
Insta's 907 manual has no fault chart, but its operating and safety notes explain what the press needs before it will cycle. Go through these in order.
Match your symptom
| What you see | Check first |
|---|---|
| Won't close | Arm position, buttons, air |
| Closes, opens at once | Timer, DISENGAGE |
| Weak press | Regulator, compressor, pad |
| No heat | Sleep, auto off, circuit |
Won't close
-
Line up the arm
For safety, the 907 won't operate unless the upper arm is directly over one of the two lower platens. Swing it until it stops squarely over a station.
-
Hold both buttons until contact
Press and hold both start buttons together and keep holding until the lower platen touches the heated platen. A safety delay is on by default, so a quick tap does nothing.
-
Check the air
The gauge should read between 30 and 100 psi. Make sure the compressor is on, its tank is charged and the line valve is open. Never go above 100 psi.
-
Reset after DISENGAGE
If DISENGAGE was pressed, the cycle stopped and the timer reset. Start again.
Opens too soon
- Press PGM to see which preset is active, then show its timer. The timer reads minutes:seconds, from 00:00 to 10:00.
- If no preset light is lit, you're on the manual setting, which keeps its last value.
Weak or uneven pressing
- Raise the regulator a little at a time and test.
- If the gauge drops during a cycle, the compressor may be too small or the hose may leak. Listen for hissing.
- Check for water in the regulator bowl and drain it (see the maintenance guide).
- Look at the silicone pads. A cut or flattened pad gives soft spots.
No heat
-
Wake it up
Sleep mode drops to the set back temperature, and auto shut off turns heat off after the idle time you set. Press any key, then check the times in the controller menu.
-
Check the circuit
Use a separate 15 A circuit at 120 V and a proper extension cord, if any.
-
Check the reading
If the platen heats but transfers act wrong, compare the display with a surface probe and use the user offset.
Before you contact us
- Note your model and serial number from the label on the press.
- Write down the air gauge reading while idle and during a cycle.
- Note which preset light is on and the temperature and time it shows.
- Record a short video of the arm position and what happens when you hold both start buttons.
The 907 has a 1 amp fuse, a micro switch and live terminals inside its housing. Don't open it. Text us a short video of what happens when you press start, plus your serial number, at (562) 609-4996.
Watch Insta's video: how to use and operate the Insta 907
Embedded from the manufacturer's official channel.
Common questions
I hold both buttons and nothing happens.
Move the arm until it's squarely over one lower platen, check the air gauge, then hold both buttons for at least a second and until the platens touch.
It closes and pops right back open.
Check the timer on the active preset, and make sure DISENGAGE wasn't pressed.
Labels aren't sticking well.
Raise the air pressure a little at a time within 30 to 100 psi and confirm the temperature with a surface probe.
The display is on but it's cold.
It's probably in sleep mode or auto shut off. Press a key. If it still doesn't heat, contact us.
- Insta Model 907 Operation and Maintenance Manual (MNL90000 Rev. L)
- Insta Models 907 and 914 Operation Manual (Rev. E)
- AA support requests about Insta presses, 2024 to 2026











































































