Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Miro 36 (Gen 2) daily operation: control panel, temperatures, loading film and ending a run
Center the Miro 36 on the film with the ruler on the front heating plate, lock it, and set the media wheels to your film width (add a wheel within 10 cm of the sensor on narrower film). Start at 60°C preheat, 130°C main heat and paddle speed 5, keep the purifier fan on, and keep powder below the media wheel rod. At the end, advance the film 800 to 900 mm and let the last section cure 3 to 5 minutes.
This covers the Miro 36 with the touch control panel (Gen 2). The steps are the same on the 110V and 220V models; only the power hookup differs. For the newer Miro 36 Pro, see our Miro 36 Pro operation guide.
Power and safety basics
| Model | Power |
|---|---|
| 110V | Two power ports. The upper one runs the main heating plate and take-up reel (up to 18 A); the lower one runs the preheating plate and powder shaking (up to 8 A) |
| 220V | One power port, about 10 A in total |
The power button is on the right side, next to the screen. Opening the powder station cover stops the paddle, opening the cover stops the take-up motor, and opening the heating chamber turns its heat off right away. To raise the control panel, press the black metal areas at its bottom edge with both hands until it clicks. Never push on the screen itself.
The controls you'll use
- Shaking paddle: press the number button under the speed bar to turn it on, then the arrows to change intensity. About 5 is the recommended starting point.
- Purifier fan: the on/off button under the speed bar turns green when on and red when off. Keep it on whenever you print. There are two fan switches; either one is enough for normal printing, alternating them extends fan life, and turning on both helps if smoke persists.
- Temperatures: tap the temperature number to enter new values for the front preheating plate and the main heating plate.
- Advanced settings: switch between Celsius and Fahrenheit, restore factory settings, or calibrate temperature if the display doesn't match a thermometer.
Daily start-up
-
Check the printer first
Print a nozzle check and make sure it is clean before you involve the shaker.
-
Position the Miro 36
Take off the fabric cover, lift the front heating plate and match its height to the printer. Move the Miro 36 up to the printer, let the film out to the edge of the preheating plate, center the machine on the film using the ruler on the front plate, and lock the stopper.
-
Set the media wheels
Take the media wheel rod out of the powder station, loosen the wheel screws and set the wheels to your film width. Leave them snug, not tight, so you can fine-tune during printing. On film narrower than 36 inches, add an extra media wheel and keep it within 10 cm of the sensor so the sensor can still see it.
-
Preheat and feed
Turn the Miro 36 on and set the preheat to 60°C, adjusting for your film. Start the print and pause when it reaches the end of the preheating plate. Open the powder station and heating chamber, slide the film into the chamber, clip it with the clamps and close the lid to hold them.
-
Cure and powder
Set the main heat to 130°C and resume printing. When the extra film forms a U shape, pause, open the powder station, lay the media wheel rod on the film and add a small amount of powder in the groove. Close the cover.
-
Start the paddle, purifier and reel
Turn on the paddle at about 5 and the purifier fan, then resume. Pull the clamped film toward the take-up reel, turn on the reel motor, remove the clamp once there is slack, route the film under the tension rod, line it up with the preheating plate and tape it to the core. Top up the powder, never above the media wheel rod.
Don't leave the Miro 36 unattended during your first two weeks. Watch print quality, powder coverage and cure, and make sure excess powder is cleared before the film enters the oven. Raise the main heat if the powder looks under-cured.
End of the print run
-
Advance the film
Use the printer's feed function to advance the film 800 to 900 mm, and set the front heating to 0 so it starts cooling.
-
Release it from the printer
When the feed stops, detach the film from the printer and let it slide into the powder station. Don't let go too early. Use the cover to move the last printed film into the oven.
-
Cure and wind
Give the last section 3 to 5 minutes to cure. Turn off shaking and preheat, let the reel pull in the rest, then turn off the reel motor and remove the core.
Then do the end-of-day cleaning in our Miro 36 maintenance guide. Too much powder coming out, the paddle not shaking, or the reel pulling nonstop? Text us a photo or short video at (562) 609-4996.
Watch DTF Station's daily operation walkthrough for the Miro 36
More videos
Embedded from the manufacturer's official channel.
Common questions
What paddle speed should I use on the Miro 36?
DTF Station recommends starting around 5 and adjusting to how your powder behaves.
Why does my 110V Miro 36 have two power cords?
The upper port powers the main heating plate and take-up reel (up to 18 A) and the lower port powers the preheating plate and powder shaking (up to 8 A). The 220V model uses one port at about 10 A.
My film is narrower than 36 inches. What changes?
Add an extra media wheel and keep it within 10 cm of the sensor, so the sensor can still detect the wheel and run the machine automatically.
Why do both purifier fan switches exist?
Each switch runs a diagonal pair of fans. Either one handles normal printing, alternating them extends fan life, and running both helps clear persistent smoke.
Why did everything stop when I opened a cover?
That's the safety system. The paddle, take-up motor and chamber heat all stop when their covers open, and resume once closed.
- DTF Station: Miro 36 operation guide
- DTF Station: Miro 36 quick start guide (initial setup)
- DTF Station technical documentation
- AA support requests about the Miro 36, 2024 to 2026











































































