Support
Machine type
Brand
Pearl Elite and Pearl PTM DTG pretreatment machines

Pearl Elite and PTM daily flush, cleaning, power down and changing pretreat

✓ Reviewed by Jason KimUpdated 2 min readFits: Pearl Elite · Pearl PTM
Short answer

At the end of every day, prime the pretreat out of the line, flush with distilled water until it runs clear, take the nozzle out and store it in distilled water, then power down from the Maintenance menu. Pearl says skipping the daily flush can damage many parts and isn't covered by the Elite warranty. Use distilled water only, and on the Elite never let pretreat sit idle for more than 30 minutes.

End of every working day

  1. Prime the pretreat out

    Open the Maintenance menu. Lift the inlet hose out of the pretreat jug, put a cup under the nozzle and run Pretreatment Auto Prime or hold Pretreatment Manual Prime until the line is nearly clear. You can pour that pretreat back into the jug.

  2. Flush with distilled water

    Put the hose in a jug of distilled water and run Water Auto Prime or hold Water Manual Prime into the cup. Keep going until no pretreat is left in the lines. Pearl notes this can take several prime cycles or several cups of water.

  3. Store the nozzle wet

    Twist off the nozzle cap, remove the nozzle and drop it in a small cup of distilled water overnight. Leave distilled water in the lines.

  4. Power down from the screen

    In the Maintenance menu press Power Down. The cart parks at home, then press OK and switch the power off (O). This saves your settings, cycle count and level meters. If the lines still hold pretreat, the machine won't let you power down.

Pearl warns that skipping the daily flush can damage many components, and the Elite warranty doesn't cover that damage. On the Elite, don't let pretreat sit in the machine for more than 30 minutes: flush it out if you'll be away longer.

Keep the inside clean

Pretreat dries into salt deposits that make the cart and drawer stick. Wipe off the excess with shop towels, then go over the body with an all-purpose cleaner. On the Elite, open the side and front windows, or pull the drawer out with its release tabs. Pearl asks for this after every use on the Elite and after every 10 shirt cycles on the PTM.

Changing between pretreats

The level meters and cost counters work out usage from the prime buttons, so follow this order or the counts drift:

  1. Empty the old pretreat

    In Maintenance, lift the hose out and prime the line nearly clear into a cup. Pour it back into its jug.

  2. Flush with distilled water

    Hose into distilled water, then Water Auto Prime or Water Manual Prime until the line is clean. Take the hose out of the water.

  3. Switch the selection

    Press the Light/Dark Pretreatment Selection icon to choose the pretreat you're changing to, then prime with the pretreatment button until the water is out of the line. Discard the water in the cup.

  4. Prime the new pretreat

    Put the hose in the new jug, cup under the nozzle, prime and let the pressure build before you spray a shirt.

Keep the level meter honest

The meter assumes a gallon. When you open a full gallon, go to the Stats menu and press Reset Level Meter for that pretreat. Every brand of pretreat flows a little differently, so if the meter hits empty before the jug does, lower the viscosity (tap Cost/Shirt in the Stats menu and move the slider). If it hits empty after, raise it.

Watch Pearl's video: cleaning and purging the spray nozzle

Embedded from the manufacturer's official channel.

Common questions

Can I use tap water to flush?

Pearl's Elite manual says to flush with distilled water only. Use distilled on both models.

The screen won't let me power down. Why?

Pearl blocks the power-down until the fluid lines have been flushed with water. Finish the flush, then press Power Down in the Maintenance menu.

What should I leave in the lines if I'm closed for a week?

Distilled water. Pearl recommends leaving distilled water in the lines for long breaks because it makes the next prime easier. Store the nozzle in distilled water too.

My level meter says empty but the jug isn't. How do I fix it?

Reset the level meter only when you start a full gallon. If the meter runs out before the jug does, lower the viscosity setting (Stats menu, tap Cost/Shirt). If it runs out after, raise it.

How often do I clean inside?

Pearl says after every use on the Elite and after every 10 shirt cycles on the PTM, because dried pretreat leaves salt deposits that stop things moving.

Did this fix it?