Support
Machine type
Brand
Pearl Elite and Pearl PTM DTG pretreatment machines

Pearl Elite or PTM leaking or dripping pretreat: find the cause

✓ Reviewed by Jason KimUpdated 2 min readFits: Pearl Elite · Pearl PTM
Short answer

Pearl traces most drips to the nozzle assembly: a loose nozzle cap, a missing nozzle O-ring, or on the Elite a missing check valve. A drip at the solenoid usually means its hose has slipped out of the quick-connect. Pretreat on the table behind the machine points to a loose pump hose inside, so power off and text us before you open a panel. Some pretreat on the bottom pan after spraying is normal.

Match your symptom

Where it drips Most likely cause (Pearl) Fix
From the nozzle, more than a drop or two after a pass Nozzle cap loose, O-ring missing, or (Elite) check valve missing Steps 1 and 2
From the solenoid above the nozzle Hose slipped out of its quick-connect Step 3
From the back or bottom of the machine, or the table behind it is wet A pump hose has come loose inside Step 4
Pretreat film on the bottom pan Normal overspray Step 5

Step by step

  1. Tighten the nozzle cap

    The cap is a quick twist-on fitting. A cap that isn't fully home lets pretreat seep around the nozzle. On the Elite, open the front window to reach it. Twist it snug by hand.

  2. Check what's inside the cap

    Twist the cap off over a cup. Pearl's order is: nozzle into the cap, the rubber seat (O-ring) on top of the nozzle, then on the Elite the check valve on the rubber seat. A missing O-ring lets pretreat run past the nozzle. A missing or worn check valve lets the line drip after the spray stops. Replace any part that's torn, flattened or missing, then twist the assembly back on.

  3. Reseat the solenoid hose

    If the drip comes from the solenoid just above the nozzle, Pearl says the hose has probably come loose. Turn the machine off, then push the hose firmly back into the quick-connect until it stops.

  4. Leaks from the back: stop and call

    Pearl's table points to a pump hose that has come out of its quick-connect behind a cover panel. Turn the power off, unplug the machine, wipe up and don't keep spraying. Text us a photo of where it's wet before you open anything. On the Elite, Pearl's warranty excludes damage from removing the top cover.

  5. Clean the normal overspray

    Pearl says pretreat collecting on the bottom pan is normal. Left there it builds up salt deposits, so wipe it out with shop towels and then all-purpose cleaner: after every use on the Elite, after every 10 shirt cycles on the PTM.

Turn the machine off before you reach inside, and never reach in during a spray cycle. Wear the gloves and eye protection your pretreat maker recommends.

Still leaking after the cap, O-ring, check valve and hose checks? Text us a short video at (562) 609-4996 and tell us which model you have.

Watch Pearl's video: cleaning and purging the spray nozzle

Embedded from the manufacturer's official channel.

Common questions

Is pretreat on the floor of the cabinet a leak?

No. Pearl says a build-up on the bottom pan after spraying is normal. Wipe it out with towels after every use (Elite) or every 10 cycles (PTM).

I replaced parts and it still pours from the nozzle. What next?

If the nozzle cap, O-ring and check valve are all in place and it still runs when it shouldn't spray, text us a short video at (562) 609-4996. Pearl's table doesn't cover a nozzle that won't shut off, and the solenoid is a wear part.

What does the check valve do?

On the Elite it sits on the rubber seat inside the nozzle cap and stops the nozzle dripping after each spray cycle. If it's missing or worn, you'll see drips on the shirt.

Can I take the top cover off to find a leak?

Not on the Elite. Pearl's warranty excludes damage from removing the top cover without authorization. Contact us first.

Did this fix it?