Support
Machine type
Brand
Pearl Elite and Pearl PTM DTG pretreatment machines

Pearl Elite or PTM not priming, no suction or uneven spray: how to fix it

✓ Reviewed by Jason KimUpdated 2 min readFits: Pearl Elite · Pearl PTM
Short answer

Most Pearl priming problems come from a hose that isn't pushed all the way into the quick-connect inlet, an empty jug, or pretreat that dried in the line or nozzle. Seat the hose firmly, prime from the Maintenance menu with a cup under the nozzle and let the pressure build. A new machine can need up to 30 seconds of holding the prime button, or a first prime with the nozzle cap off. A lopsided or narrow spray usually means a clogged nozzle: clean it or replace the nozzle and its O-ring.

Match your symptom

What you see Most likely cause Go to
Nothing comes out when you prime, or no suction Hose not seated, empty jug, or first prime on a dry line Steps 1 to 3
Nothing comes out after the machine sat with pretreat in it Pretreat dried in the line or nozzle Step 4
Spray sputters or comes and goes Jug low or empty, air in the line Steps 1 and 3
Heavy on one side, light on the other, or not the full platen width Clogged nozzle Steps 4 and 5
Spray band is tilted Nozzle sitting crooked Step 5
Cart stops or sputters while it moves Loose belt or dry rail Step 6

Step by step

  1. Check the jug and the selection

    Make sure the hose end sits well under the liquid and the jug isn't nearly empty. Pearl lists a low or empty container as the cause of an inconsistent, sporadic spray. In the Maintenance menu, use the Light/Dark Pretreatment Selection icon to pick the pretreat you're actually running before you prime.

  2. Push the hose all the way in

    The inlet is a quick-connect for 1/4 inch hose. Pearl warns the unit may not prime if the hose isn't fully inserted and firmly seated. Pull it out, check the end is cut clean and not split, and push it in until it stops.

  3. Prime and let the pressure build

    Open the Maintenance menu, put a cup under the nozzle (on the Elite, open the front window first) and hold Pretreatment Manual Prime, or press Pretreatment Auto Prime. Give it time: the pressure has to build before you get a clean flat spray. On a first fill or a line that ran dry, Pearl says you may need to hold the button for up to 30 seconds, or prime with the nozzle cap removed. Pour the excess back into the jug.

  4. Clear dried pretreat

    If the machine sat with pretreat in it, move the hose to a jug of distilled water and prime water through with Water Manual Prime until it runs clear. It can take several cups. Twist off the nozzle cap and clean the nozzle with cleaning solution. Pearl's video shows how to clean and purge it.

  5. Reseat or replace the nozzle

    A tilted band means the nozzle is sitting crooked: reposition it so the spray is straight across the platen. If one side stays heavy or the band is narrow after cleaning, replace the nozzle (TeeJet TP9501EVS) and its O-ring. Rebuild the cap in Pearl's order: nozzle into the cap, rubber seat on top, then the check valve, and twist the cap onto the nozzle body.

  6. Fix a cart that stalls

    Pearl lists two causes: a loose drive belt and a dry rail. On the PTM, spray the rail with a silicone lubricant, then press the rail on the Maintenance screen to run the cart and spread it. Pearl's PTM manual also shows how to tighten the belt from the motor plate with a 3 mm hex key. On the Elite the belt sits under the top cover, and Pearl's warranty excludes damage from removing that cover, so text us instead.

If the cart stalls during homing, the screen won't respond, or the pump runs but won't pass clean water, stop and text us a photo or short video at (562) 609-4996. Pearl treats nozzles and solenoids as wear parts, so tell us when you last replaced them.

Once it sprays cleanly again, set up the daily flush in our Pearl cleaning guide so the line doesn't dry out again.

Watch Pearl's video: cleaning and purging the spray nozzle

Embedded from the manufacturer's official channel.

Common questions

I just put in a new nozzle and now there's no suction. Why?

Check the hose first. Pearl warns the machine may not prime if the hose isn't fully inserted and firmly seated in the quick-connect inlet. Then prime with the nozzle cap off for the first fill, and reassemble the cap in Pearl's order: nozzle, rubber seat, then check valve.

Auto Prime runs but the line still has air or old pretreat in it. What do I change?

Hold the Manual Prime button instead, or raise the auto prime time. On the Elite, Pearl puts that under Maintenance, then the Adjust button, then the AUTO slider.

What nozzle does the Pearl use?

A TeeJet TP9501EVS on both the Elite and the PTM. Keep a spare, plus spare O-rings and a check valve.

How do I know how many grams a density setting puts down?

Pearl only rates the full range (about 12 to 60 ml over the full area), so weigh a shirt before and after spraying. Our guide to how much pretreat to use walks through it.

The pump hums but nothing comes out even with fresh water. What now?

Stop there and text us a short video at (562) 609-4996. A pump or solenoid that won't pass water needs a closer look.

Sources
Did this fix it?