Support
Machine type
Brand
DTF Station Prestige A3+ and A3+ R

Prestige A3+ and A4 daily maintenance: start-of-day and end-of-day routine

✓ Reviewed by Jason KimUpdated 2 min readFits: Prestige A3+ · Prestige A3+ R · Prestige A4
Short answer

Every morning: check the waste bottle, shake the white ink, check the dampers, then run a head cleaning and a nozzle check on film, and don't print until it's solid. Every evening: clean the capping station, wiper and the area around the print head with DTF cleaning solution, park the head on the cap, and power down. Once a week, clean the encoder strip. Five to ten minutes a day prevents most clogs and blinking lights.

What you need

  • DTF printer cleaning solution
  • Foam or polyester cleaning swabs, including a long one for reaching around the head
  • Paper towels and gloves
  • Isopropyl alcohol (90% or stronger) and a lint-free cloth, for the weekly step only

Start of the day

  1. Check the waste side first

    Look at the waste ink bottle and empty it before it's close to full. If you clipped the waste tube last night, remove the clip now, before any cleaning runs.

  2. Check the ink

    Make sure every color has enough ink. Shake the white ink bottle, and any spare white you're storing, for about 30 seconds.

  3. Check the dampers

    Look at the dampers on top of the print head and make sure each is pushed fully into place.

  4. Power on

    Turn on the switch at the back, wait a few seconds, then press the front power button. Wait until the power light stops blinking.

  5. Head cleaning and nozzle check

    In DigiRip, open Devices > Printer Properties, run a head cleaning, and print a nozzle check on DTF film. You need a solid pattern before you print. If it has gaps, follow our nozzle check and clogs guide.

End of the day

  1. Move the carriage off the cap

    Release the print head from the capping station so you can reach the cap and wiper, and gently slide the carriage aside. Your training video shows how on your model. Text us if you're not sure.

  2. Clean the cap and wiper

    Put paper towels down. Dip a swab in cleaning solution and clean the rubber cap, its top edge and the wiper blade until no ink comes off. Then go over them with a dry swab.

  3. Clean around the print head

    With a long swab and cleaning solution, clean around the edges of the print head, where ink and powder build up. Don't scrub the nozzle face.

  4. Optional: wet the cap overnight

    Clip the waste ink tube so it can't drain, then add a little cleaning solution to the cap, stopping well below the lip. This keeps the nozzles moist overnight. Remember to remove the clip first thing tomorrow.

  5. Park the head and power down

    Return the carriage so the head seals on the cap. Turn the printer off at the front button, wait a few seconds, then switch off at the back. Close the covers and trays and put a dust cover on the printer.

Once a week

  • Encoder strip: with the printer off, gently pinch the clear strip behind the carriage in a lint-free cloth dampened with isopropyl alcohol and wipe it end to end. A dirty strip causes blurry prints and red lights blinking together.
  • Printer bed and guides: wipe off ink and powder dust with isopropyl alcohol on a cloth.

Never spray or pour liquid inside the printer, and keep alcohol off rubber parts like the cap and wiper.

Questions about any step? Text us a photo or short video at (562) 609-4996.

Watch DTF Station's video: Prestige A4 daily maintenance

More videos

Prestige A4 opening procedure
Prestige A3+ R opening procedure
Prestige closing procedure
Prestige A4 weekly maintenance

Embedded from the manufacturer's official channel.

Common questions

Can I use alcohol or a household cleaner on the cap and wiper?

No. Use DTF cleaning solution made for printers. If you're out, plain distilled water with nothing added is a safer stopgap than any household cleaner, which can damage the rubber and stain the head. Save isopropyl alcohol for the encoder strip and the printer bed.

Should I swab the bottom of the print head?

Clean around the edges of the head, not the nozzle face itself. Rubbing the nozzle plate can damage it.

Do I really need to do this if I only print once a week?

Yes. A printer that sits is more likely to clog than one that's used. Run the morning routine every day you print, and see our idle and storage guide for longer breaks.

Why turn it off at the front button first?

The front button lets the printer finish and park the head properly before the power is cut. Wait a few seconds, then switch off at the back.

Sources
Did this fix it?