Support
Machine type
Brand
DTF Station Prestige A3+ and A3+ R

Prestige A3+ and A4 nozzle check gaps and clogs: how to clean the head the right way

✓ Reviewed by Jason KimUpdated 2 min readFits: Prestige A3+ · Prestige A3+ R · Prestige A4
Short answer

Run head cleanings and nozzle checks from DigiRip under Devices > Printer Properties, and print the check on DTF film so you can see the white. A few missing nozzles just need another cleaning. One whole color missing points to that color's damper or ink line. Heavy gaps across the head need a pull through the waste line, which we'll walk you through. Don't run cleaning after cleaning: each one uses ink and fills the waste counter.

Match your nozzle check

What you see Most likely cause What to do
A few scattered gaps Partial clog Steps 1 to 3
One color completely missing, others fine That color's damper or ink line Step 4
Heavy gaps across most colors Heavy clog, or the cap isn't sealing Steps 3 and 5
Good check in the morning, gaps after a few prints Head touching the film, air blowing on the head, or a dirty cap Step 5, and check the room
Nothing prints at all, not even a partial pattern Electrical or connection fault Text us before cleaning further

Step by step

  1. Start with the daily basics

    Shake the white ink, make sure there's ink in every bottle, and check the dampers on top of the print head are pushed fully into place. Turn the printer on and wait until the power light stops blinking.

  2. Run a head cleaning from DigiRip

    With the printer on and connected by USB, open DigiRip and go to Devices > Printer Properties, then run a head cleaning. Wait until the blinking power light goes solid before you do anything else.

    Never turn the printer off during a cleaning cycle.

  3. Print a nozzle check on film and read it

    Load DTF film and print the nozzle check pattern from the same window. If only a few nozzles are missing, run another cleaning and check again. You want a solid, complete pattern before printing production work. Take a photo of each check: we'll ask for them if you contact us.

  4. One color missing? Check that color's ink path

    When a single channel is gone while the rest print, the head usually isn't the problem. Check the bottle for that color has ink, the line isn't kinked, and there's no long air gap in the tube above the damper. A damper that won't hold ink or has a leaking seal needs replacing. Hold dampers by their outer frame only, never by the soft center.

  5. Heavy gaps? Clean the cap, then pull through the waste line

    Clean the capping station with DTF cleaning solution and a swab: a dirty or dried cap can't create the suction a cleaning needs. Then run one more cleaning. If gaps are still heavy, the next step is a pull: with the head parked on the cap, ink is drawn through the head with a syringe on the waste ink line.

    Pulling too hard or too often can damage the head and the pump. Text us the first time and we'll walk you through it on your model.

When to stop and contact us

  • The pattern doesn't change at all after several cleanings and a pull.
  • No ink moves through the waste tube during a cleaning.
  • The cap doesn't rise to meet the head, or the head doesn't park on it.
  • The red lights start blinking during cleaning.

Text us a photo or short video at (562) 609-4996. Send your latest nozzle check photo with it.

Watch DTF Station's video: nozzle check and head cleaning on the Prestige A4

Embedded from the manufacturer's official channel.

Common questions

How many head cleanings should I run in a row?

Run one, then print a nozzle check and look. If it's improving, run another. If two or three cleanings change nothing, stop and look for the cause in the table above. Endless cleanings waste ink and fill the waste ink counter, which eventually stops the printer with alternating red lights.

Why print the nozzle check on film instead of paper?

White ink doesn't show on white paper. Use DTF film so you can see every channel, and lay it on something dark to read the white.

Printer Properties won't open in DigiRip. What's wrong?

Check the printer is on, then go to Queue > Manage Queues and make sure the queue uses the printer's USB port. Also confirm the printer's control software was installed during setup.

How often should dampers be replaced?

About once a year with regular use. A damper that's been pulled out and reseated many times wears out sooner.

When is it the print head?

Print heads typically last 1 to 2 years. If the cap, wiper, dampers and ink lines check out and the same nozzles stay missing, the head may be worn. Text us the nozzle check before you buy one.

Sources
Did this fix it?