Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige R2 Pro and R2 capping station and wiper blade wear: signs, what to order, and when to call us
The cap tops and the wiper blade are wear parts: DTF Station expects them to need replacing every 1 to 2 years. Clean them first, then watch a head cleaning. Ink bubbling at the cap, a torn or hardened cap seal, or a bent wiper means the part is worn. A capping station that no longer rises, grinds, or throws error 4000 needs the full assembly, and its heights are set in protected software menus, so text us before you swap it.
What these parts do
The capping station sits under the heads at the right side of the printer. It has three working parts:
- Cap tops: one under each head. The cap has two layers. During a cleaning, the inner layer presses against the head to make an airtight seal so the pump can pull ink through the nozzles.
- Wiper blade: after a cleaning, it rises and wipes the head face like a windshield wiper.
- Pump, tubes and sensor: they pull ink to the waste bottle and tell the printer where the station is.
Anything that touches ink wears. DTF Station expects the cap tops and wiper blade to need replacing every 1 to 2 years.
Match your symptom
| What you see | Likely worn part | What to do |
|---|---|---|
| Ink bubbles or foams at the cap during a cleaning | Cap seal torn or hardened, or cap off-center | Steps 1 to 3, then order a cap top |
| Nozzles won't recover even after a wet cap | Cap not sealing, or wiper not reaching the head | Steps 1 to 3 |
| Wiper bent, torn, slanted, or missing part of the head | Wiper blade | Order a wiper blade, text us to fit it |
| Wiper flicks ink sideways, or doesn't touch the head | Wiper height setting | Text us |
| Capping station doesn't rise to the head, grinding noises, error 4000 | Capping station mechanism or sensor | Text us before ordering |
Check before you order
-
Clean it first
A dirty cap looks like a worn one. Press the Left arrow to move the head off the caps. With a foam swab and DTF Station-approved cleaning solution, clean the cap tops, the plastic around them and the wiper blade, then dry the wiper with a clean swab. Press Enter to dock and run one head cleaning.
-
Look at the cap and wiper
Open the capping station compartment and use a flashlight. Look for a cap seal that is torn, cracked, hard or caked with dried ink, and a wiper blade that is bent, nicked or leaning. Press Enter a few times and watch the cap rise. It should sit centered under the head.
-
Watch a head cleaning
Film a head cleaning at eye level from an angle. The inner layer of the cap should press firmly against the head without lifting the carriage. Bubbling or foaming means air is getting in. After the cleaning, the wiper should rise and wipe the whole width of the head, touching evenly without bending hard.
-
Send us the videos
Text us the nozzle check photo, the cleaning video, and a short clip of you pressing Enter. From these we can usually tell whether you need a cap top, a wiper, a height adjustment, or the full assembly.
What to order
| Part | Prestige R2 Pro | Prestige R2 (original) |
|---|---|---|
| Cap top | Cap top for i1600 and i3200 printheads | Cap top for XP600 |
| Wiper blade | Wiper blade (110mm) | Wiper blade (110mm) |
| Full assembly | Capping station assembly for R2/R2 Pro | Capping station assembly for R2/R2 Pro |
Replacing the whole capping station means unplugging cables at the back of the printer and then setting the cap and wiper heights in a password-protected menu. Too high and the cap wears the head; too low and the cleanings stop working. We do that part with you on a call.
Make them last
- Clean the cap tops and wiper every day at end of day, and wet the cap sponges with a syringe of cleaning solution before you dock and run one cleaning.
- Use only DTF Station-approved cleaning solution on the caps and wiper.
- Leave the printer on with the head docked overnight, so it stays sealed and runs its idle cleaning.
- Clear any head strike right away. Film residue picked up by the head gets smeared by the wiper during every cleaning.
Not sure what you're looking at? Text us a photo or short video at (562) 609-4996 and we'll tell you which part to order.
Watch DTF Station's video: replacing the capping station on the Prestige R2 and R2 Pro
Embedded from the manufacturer's official channel.
Common questions
How long do cap tops and wiper blades last?
DTF Station's own estimate is 1 to 2 years. Skipping the end-of-day cleaning, or using the wrong cleaning fluid, shortens that.
Is the cap top the same on the R2 and the R2 Pro?
No. The R2 Pro uses Epson i1600 heads and takes the cap top for i1600 and i3200 heads. The original R2 uses XP600 heads and takes the XP600 cap top. The wiper blade and the full capping station assembly are listed for both.
Can I just raise the wiper or cap a little myself?
Not on these printers. Cap and wiper heights are stored in a password-protected menu, and too much pressure wears the head and the cap. Send us a video and we'll set them with you.
My nozzle check got worse right after I replaced the cap. Why?
A new cap that sits slightly off-center, or a tube that isn't pushed fully onto the cap, lets air in during cleaning. Send us a video of a head cleaning and of the cap rising.
Does cleaning fluid really matter?
Yes. DTF Station has seen the wrong cleaning fluid ruin the head, the cap and the wiper together. Use a DTF Station-approved cleaning solution only.
- DTF Station: Prestige R2 and R2 Pro, how to replace the capping station
- DTF Station: Prestige R1 and R2, troubleshooting poor nozzle checks (capping station)
- DTF Station: Prestige R2 Pro maintenance guide
- DTF Station: Prestige R2 Pro user manual (maintenance schedule)
- DTF Station technical documentation
- AA and DTF Station support requests about capping stations and wiper blades, 2024 to 2026











































































