Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige R2 Pro and R2 carriage problems: print stops mid-job, error 01604, belt and encoder strip
If the carriage stops mid-print or freezes and the log shows 01604, the printer lost track of the carriage position: the usual causes are belt tension, the bearing, or a dirty encoder strip. Start by cleaning the encoder strip with 90% or stronger isopropyl alcohol. Blurry or doubled prints after a film change need a step (feed) calibration. Belt, bearing, encoder and motor work all end with a carriage calibration in the control software, so text us before you start one.
Match your symptom
| What you see | Likely cause | Go to |
|---|---|---|
| Print stops partway, carriage freezes, log shows 01604 | Belt tension, bearing or encoder | Steps 1 to 3 |
| Blurry or doubled prints, white shifted from color | Dirty encoder strip or step calibration | Steps 2 and 5 |
| Carriage squeaks | Dry rail | Step 4 |
| Carriage moves left but never right | Home sensor | Contact us |
| Red light on the X motor (side panel) | Carriage motor fault | Contact us |
| Grinding at startup, error 4000 | Capping station, not the carriage | Our error codes guide |
Step by step
-
Read the log
In Pilot or Hosonsoft, click the light bulb icon and open the Log. Note every code in red. 01604 points to belt tension or the bearing, and 016004 to the encoder strip, encoder sensor or carriage board. If the printer is frozen, power off, wait 5 seconds and power on first.
-
Clean the encoder strip
The encoder strip is the clear strip running across the printer behind the carriage, and the carriage reads its position from it. Dampen a lint-free cloth with 90% or stronger isopropyl alcohol, pinch the strip gently and wipe side to side along the whole length, moving the carriage to reach the part it covers. Make sure the strip sits centered in its brackets and isn't twisted, because a misplaced strip can damage the strip or the motor. Press Enter to let the carriage reset. A strip that is scratched, dented or bent must be replaced.
-
Look at the belt
With the printer off, move the carriage by hand and watch the belt. It should move with the carriage without slipping, fraying or sitting loose. A belt that shifts or looks worn needs re-tensioning or replacement. Tensioning is done at the carriage motor mount, so we do that one with you.
-
Grease a squeaky rail
If the carriage squeaks, apply a heat-resistant gel or paste grease to the rail. Never use a spray lubricant.
-
Recalibrate after a film change
Doubling or a white layer that sits off the color layer usually means the step (feed) calibration is off for this film. In Hosonsoft it's under Adjust > Step Adjust > Base Step > Print Adjust, and in Pilot under Calibration > Step Calibration. Print the pattern, pick the value where the lines form a single solid line, enter it and reprint until the best line lands on zero. Have at least 90% of nozzles firing first.
After replacing the belt, the right bearing, the encoder strip or the carriage motor, the printer needs a carriage gear-ratio calibration in the control software's protected settings. Entering a wrong value there can cause new errors, so text us and we'll do it with you on a call.
Still stopping mid-job? Text us a photo or short video at (562) 609-4996 of the carriage when it stops, plus a screenshot of the log.
Watch DTF Station's video: troubleshooting the print pause issue on the Prestige R2 and R2 Pro
Embedded from the manufacturer's official channel.
Common questions
The print stops partway and the printer won't respond. Is it broken?
Not necessarily. Power off, wait 5 seconds, power on, then check the log for 01604 before you try anything else.
Why are my prints blurry or doubled?
A dirty or damaged encoder strip is the first suspect, then the step calibration. Recalibrate whenever you change to a different film.
My step calibration value changes every time I run it. Why?
Something in the film path is inconsistent: film tension, the pinch rollers, the film itself, or the media roller attachment. Fix those before calibrating again.
Can I replace the carriage belt myself?
Yes, with DTF Station's video and the right tools, but it ends with a carriage calibration in the control software. Text us before you start and we'll be ready to finish it with you.
- DTF Station: Prestige R2 Pro, troubleshooting when the print head carriage does not move properly
- DTF Station: Prestige R2, troubleshooting the print pause issue
- DTF Station: Prestige R2, how to inspect and clean the encoder strip
- DTF Station: Prestige R2, how to replace the carriage belt
- DTF Station Prestige R2 Pro user manual: maintenance schedule
- DTF Station technical documentation
- AA and DTF Station support requests about Prestige carriage and belt problems, 2024 to 2026











































































