Support
Machine type
Brand
DTF Station Prestige R2 (original)

Prestige R2 Pro and R2 maintenance: daily, end of day, weekly, and when it sits idle

✓ Reviewed by Jason KimUpdated 3 min readFits: Prestige R2 Pro · Prestige R2
Short answer

Every morning, shake the white ink and print a nozzle check. Every evening, clean around the head, the capping station, the wiper and the cap tops with cleaning solution, wet the cap sponges, dock the head and run one cleaning, then leave the printer on with the heater and LED off. Once a week, empty the waste bottle, clean the encoder strip and suction vents with 90% or stronger isopropyl alcohol, and wipe the pinch rollers dry. Don't turn the printer off when it sits idle: it needs power to circulate white and run its automatic cleanings.

You'll need

  • Foam cleaning swabs and DTF Station-approved cleaning solution
  • A syringe
  • Isopropyl alcohol, 90% or stronger, and lint-free cloths
  • Gloves

Start of every day

  1. Shake the white ink bottle

    White ink settles. Shake the white bottle each morning, and keep any paper cover off the cap so it can't fall into the ink.

  2. Print a nozzle check before the first job

    Menu > Head Maintenance > Head Status. Print when at least 90% of the nozzles fire. If not, run a head cleaning and check again. Use Fill Ink only when big sections are missing. Always check before you clean.

End of every day

  1. Clear the film away from the head

    Use the Up and Down arrows to move the film back onto the rollers so nothing is under the head.

  2. Move the head out and clean around it

    Press the Left arrow to move the head fully left. Dip a swab in cleaning solution and carefully clean around the print head, not the nozzle face.

  3. Clean the capping station, wiper and cap tops

    With a fresh swab and solution, clean around the capping station. Wipe the wiper blade thoroughly, then dry it with a clean swab. Wipe the ink off the cap tops and the plastic around them, and dry off the excess.

  4. Wet the cap sponges

    Fill a syringe with cleaning solution and wet both cap sponges.

  5. Dock and flush

    Press Enter to send the head home onto the caps, then run one head cleaning to drain the solution through the caps and tubes.

  6. Leave it on

    Leave the printer powered on. Turn off the heater and the LED lights.

Every week

  1. Empty the waste ink bottle

    Empty it at the end of the production week, and in between if needed. Keep the waste tube pointing downward and out of the waste ink.

  2. Power down with the head in the center

    Move the film back, press the Left arrow to bring the head toward the center, then power off.

  3. Clean the encoder strip

    The encoder strip is the clear strip running across the printer behind the carriage. Dampen a lint-free cloth with 90% or stronger isopropyl alcohol, pinch the strip gently and wipe it side to side along its whole length. Make sure it sits centered in its brackets and isn't twisted. If it's scratched, dented or bent, it needs replacing, not cleaning.

  4. Clean the air suction vents

    Wipe the vents in the bed with a fresh lint-free cloth and isopropyl alcohol. Slide the media guides aside to reach them.

  5. Clean the pinch rollers dry

    Release the rollers with the lever and wipe them with a dry lint-free cloth. No alcohol and no cleaning solution. When you load a new roll, clean them all the way around.

  6. Power on and reload the film

    Route the film under the guide bar, lift the roller handle, pull the roll taut and straight from the back, and lower the handle. Bring the media guides in just enough to cover the film edges, not pressing on them. Leave the printer on, heater and LED off.

When the printer will sit idle

  • Overnight and weekends: do the end-of-day routine and leave it powered on with the head docked. The printer runs a light cleaning every 4 hours while it's parked on the caps, and keeps white ink circulating.
  • A week or more: do the full end-of-day and weekly routine, keep it powered on, and keep the room cool, dry and out of direct sun. Before you leave for longer than two weeks, text us so we can talk through your situation.
  • When you come back: shake the white, print a nozzle check, and clean or run Fill Ink only as the check shows.
  • Moving the printer: reinstall the carriage lock bracket that came out during setup and contact us before you ship it.

Watch DTF Station's video: Prestige R2 end-of-day maintenance

Embedded from the manufacturer's official channel.

Common questions

Should I turn the printer off at night?

No. Leave it powered on and turn off only the heater and LED lights. The printer circulates white ink and cleans the heads every 4 hours on its own while it sits on the capping station, and it can't do that when it's off.

Can I use alcohol on the pinch rollers?

No. Alcohol hardens and cracks the roller rubber. Use a dry lint-free or microfiber cloth only.

Can I use 70% rubbing alcohol on the encoder strip?

No. Use isopropyl alcohol of 90% or stronger on a lint-free cloth, and nothing else on the strip.

How often should the waste bottle be emptied?

At the end of each production week, and sooner if it fills. Keep the waste tube pointing down and out of the waste ink, or the suction it creates can spoil your nozzle checks.

The carriage squeaks. What do I use?

A heat-resistant gel or paste grease on the rail. Never a spray lubricant.

Sources
Did this fix it?