Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige R2 Pro and R2 dampers: how to tell if one is bad, and how to replace it
Suspect a damper when one or two channels stay missing after Fill Ink, cleanings and a wet cap, or when you see ink dripping or bubbles at the carriage. Take the damper out, hold it pointing down: if it drips, it's bad. Then pull ink through it with a syringe: steady ink with no bubbles means it's good, while backflow, bubbles or no ink means replace it. Dampers are wear parts that DTF Station expects to be replaced about once a year.
You'll need
- New damper(s) for your model
- A syringe
- Tube clamps (the clips on your ink lines)
- Paper towels, gloves and a Phillips screwdriver
- Scissors, if your tubes are stiff
Send us your nozzle check before you start. Pulling dampers without need wears their seals, and we can often tell from the photo whether a damper is really the problem.
Step by step
-
Take a baseline nozzle check
Open the front cover and, if your printer has a cover sensor, cover it as described in your setup guide. Run Menu > Head Maintenance > Fill Ink > Two Head for 30 seconds from when ink flows into the waste tank, press Cancel, run two head cleanings, then print and keep a nozzle check (Head Status).
-
Get to the dampers
Lift the pinch roller lever and roll the film back out. Open the top lid, press the Left arrow once to undock the carriage, then hold it to bring the carriage to the center. Press the Emergency Stop to power off. Loosen the screws on both sides of the carriage cover and the daughterboard cover and lift both covers off.
-
Move the white dampers out of the way
Clamp all the white ink lines and lay paper towels beside the carriage. Remove the diverter (one screw each side) and lift out the white dampers onto the towel.
-
Test the suspect damper
Clamp that color's ink line and lift the damper out by its outer plastic frame. Never press the soft side. Hold it pointing down: if ink leaks out, it's bad. Then hold it upright, put a syringe on the bottom and pull slowly. Steady ink flow means it's good. Ink flowing back when you release, no ink, bubbles or a loss of resistance mean it's bad. Reinstall good dampers carefully.
-
Fit the new damper
If the tube is soft, pull it straight off the old damper. If it's stiff, cut it straight across just above the damper nozzle. Push the tube fully onto the new damper, release the clamp, and prime it by pulling ink slowly with the syringe from the bottom until ink arrives with no bubbles. A new damper that leaks within a few seconds, sucks ink back, or won't pull ink is faulty: don't install it.
-
Put it back together
Seat the new damper, reinstall the white dampers and the diverter, and release every clamp. Refit both covers, release the Emergency Stop and let the carriage dock. Reload the film.
-
Prime and compare
Run Fill Ink on Two Head for 30 seconds once ink flows (Right Head only if you replaced a white damper), two head cleanings, and a nozzle check. Compare it with your baseline. Better means the damper was the problem. No change: text us both photos.
Not comfortable opening the carriage? Text us a photo or short video at (562) 609-4996 and we'll walk you through it.
Watch DTF Station's video: replacing a color damper on the Prestige R2 and R2 Pro
Embedded from the manufacturer's official channel.
Common questions
How often should dampers be replaced?
About once a year, along with the inlet filters.
Can I take dampers out to check them whenever I want?
Avoid it. Every removal wears the rubber seal, and a damaged seal makes a good damper go bad. Test only when a channel won't recover.
All my channels are weak. Should I replace every damper?
No. Dampers don't all fail at once. When every channel is affected, the cause is usually the capping station, the environment or settings. Text us first.
Is a little air inside the damper normal?
Yes. A damper normally holds some air with the ink. Bubbles rising into the syringe while you pull, or ink running back when you let go, are the warning signs.
Can I replace a white damper the same way?
The steps are similar, but talk to us before removing white dampers. After replacing one, prime only the white side with Fill Ink on the Right Head.
- DTF Station: Prestige R2, how to replace a color damper
- DTF Station: Prestige R2, how to replace a white damper
- DTF Station: Prestige R2, how to unclog or fix a poor nozzle check (damper test)
- DTF Station technical documentation
- AA and DTF Station support requests about Prestige dampers, 2024 to 2026











































































