Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige R2 Pro and R2 error codes and red lights: what they mean and what to do
Open Pilot or Hosonsoft and click the light bulb icon to see the error log: the code there tells you where to look. A blinking red connection icon means the computer isn't talking to the printer. A red light on the carriage board right after a repair means a ribbon cable is in wrong, so switch off before the carriage docks. Impact Stop means the head-strike sensor was touched, 01604 means the carriage lost its position mid-print, and 013047 usually means a ribbon cable got wet and shorted.
Where to look first
- Connection icon (left side of Pilot or Hosonsoft) blinking red: the computer can't reach the printer. See our connection guide.
- Light bulb icon red or yellow: there's an error. Click it to open the log. Error lines show in red. Screenshot the whole log.
- Control panel message with beeping: usually Impact Stop or a cover warning.
- Lights on the carriage: after startup the carriage should show green lights. A red light on the carriage board means trouble (below).
Common codes and lights
| Code or light | What it means | What to do |
|---|---|---|
| Impact Stop, beeping, carriage stops dead | The head-strike sensor was pushed: film lifting, a media guide, or a bent sensor guard | See our Impact Stop and head strike guide |
| 01604 (also shown as 1604), print pauses or freezes mid-job | The carriage lost track of its position: belt tension, bearing or encoder | See our carriage guide |
| 016004 | Encoder strip, encoder sensor or carriage board | Clean the encoder strip, then contact us |
| 013047 "print pass data was unfinished" | Carriage moves left, stops, returns about a minute later without printing. Usually a ribbon cable that touched ink and shorted | Steps below |
| 004000 or 4000, often with 013023, grinding at startup, carriage won't move | Capping station sensor, its cable, the capping mechanism, firmware or a board | Steps below |
| 001007 or 001009 | Carriage board (daughterboard) | Contact us with the log |
| 21106 "failed to obtain the horizontal print resolution" (the video calls it 011066) | Pilot's pass setting doesn't match the NeoStampa print mode | Steps below |
| Cover or safety cap error | The front cover sensor sees the cover open | Close the cover and retry |
| Red light on the carriage board after a repair | A ribbon cable is in the wrong slot or the wrong way round | Steps below |
| Red light on the X motor (side panel) | Fault in the carriage motor | Contact us |
Safe first steps
-
Back up before you change anything
In Pilot or Hosonsoft, export both firmware backup files (the firmware configuration and the firmware configuration parameter), using the password from your Quick Start Guide. Photograph your settings page and calibration values too.
-
21106 / 011066 when sending from NeoStampa
In Pilot, open the Log and confirm the code. Note the print scheme you used (for example 720 × 2400). Go to Advanced > Print Configuration, find that resolution and change it from 8 Pass to 16 Pass. Click Save and resend the job from NeoStampa.
-
Red light on the carriage board
Switch the printer off at once, before the carriage docks. Reseat the ribbon cables you touched: the blue-tape sides face each other, and each cable presses straight down without wiggling. Don't use a cable with bent or lifted contacts. Power on and watch the board. If the red light is still there, stop and contact us.
-
013047
Confirm 013047 is the only code. A firmware reset from your backup is the first fix. If the error comes back, DTF Station's procedure finds the shorted cable by unplugging all the ribbon cables from the carriage board and plugging them back one at a time with a nozzle check after each. It's delicate work around the board, so text us and we'll walk you through it.
-
4000 with grinding
Photograph your firmware version and send it to us first. Then, with the printer off, turn the capping station knob to lower it fully, push the carriage to the center by hand, and power on. If the capping station rises but the carriage still won't move, the capping station sensor or its cable is the likely culprit. We'll guide the sensor test with you.
For anything not listed here, Text us a photo or short video at (562) 609-4996 plus a screenshot of the full error log.
Watch DTF Station's video: resolving error 011066 in Pilot on the Prestige R2 Pro
More videos
Embedded from the manufacturer's official channel.
Common questions
The log shows several errors at once. Which one matters?
The first one in time order. The rest are usually knock-on effects. Screenshot the whole log, oldest entry included, and send it to us.
I already did a firmware reset. Doesn't that rule out firmware?
No. A reset reloads whatever version is on the machine. It doesn't confirm that the Pilot version and the printer's board firmware match, and a mismatch can cause errors, poor nozzle checks and stopped circulation. Send us photos of both version numbers.
Should I back anything up before trying fixes?
Yes. Export both firmware backup files from the control software first, and photograph your settings and calibration values. A reset without a backup loses your print start position and alignment.
Is it safe to run the printer with covers off?
Only for the specific checks in DTF Station's procedures. Never let the carriage dock with the daughterboard cover removed, and power off before touching any cable.
- DTF Station: Prestige R2 Pro, troubleshooting when the print head carriage does not move properly
- DTF Station: Prestige R2, troubleshooting error 13047 (print pass data unfinished)
- DTF Station: Prestige R2 Pro, capping station or motherboard error 4000 / 13023
- DTF Station: Resolving error 011066 / 21106 on the Prestige R2 Pro
- DTF Station Prestige R2 Pro Quick Start Guide
- DTF Station technical documentation
- AA and DTF Station support requests about Prestige error codes and red lights, 2024 to 2026











































































