Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige R2 Pro and R2 ink inlet filters and ink tubes: when to replace them and how
Each ink line has an inlet filter behind the panel at the back, between the ink bottle and the tube. DTF Station recommends replacing the inlet filters, along with the dampers, about once a year. A channel that prints well and then fades during a run, on a printer over a year old, often points to a tired filter or damper. Replacing a filter takes a screwdriver, clamps and a syringe; replacing the full ink tube assembly means removing the carriage board, so text us first.
Where they sit
Ink travels from the bottle, through an inlet filter, along a tube to the damper on the carriage, then into the head. The filters catch particles before they reach the head. They sit at the back of the printer, behind the media feed reel, under an intake filter panel held by 8 screws. Like the dampers, they are wear parts.
Signs they're due
- It's been a year or more since they were changed.
- One color prints well at first, then fades or drops out during a run.
- Nozzles slowly disappear on a printer over a year old, even with a clean cap and good dampers.
Before replacing anything, run your normal nozzle check routine and test the damper for that color. If you're unsure, text us a photo or short video at (562) 609-4996 of the nozzle check.
Replace an inlet filter
You'll need new inlet filters, ink line clamps, a Phillips screwdriver, scissors, a syringe, gloves and paper towels. Work on one color at a time.
-
Take off the film and the back panel
Raise the pinch roller lever, roll the film up, loosen the left knob counterclockwise and slide the media bracket out. Remove the 8 screws on the intake filter panel and set it aside.
-
Clamp the line
Find the filter for the color you're changing and clamp the ink line above it.
-
Park the carriage and power off
Open the top lid. Press the Left arrow once to lift the carriage off the caps, then hold it to bring the carriage to the center of the bed. Press the Emergency Stop to switch the printer off.
-
Open the carriage
Loosen, but don't remove, the screws on both sides of the carriage cover and the board cover, and lift both covers off. Clamp all the white ink lines and lay paper towels beside the carriage. Remove the diverter (one screw each side), the white dampers, and the damper for the color you're changing, and rest them on the towels.
-
Swap the filter
With towels under the filter, cut the tube straight across, as close to the filter as you can, on both sides. Push the tube from the bottle onto the side of the new filter marked INLET, with INLET facing up, until it's flush. Push the other tube onto the other side. Both must be fully seated or they'll pull air.
-
Prime the line
Unclamp the line. At the front, use a syringe to pull ink from the damper until it flows steadily with no bubbles.
-
Put it back together
Refit the dampers and the diverter, release all the clamps, and refit both covers. Release the Emergency Stop, power on and let the carriage dock. Clean up any ink, route the tubes so nothing is pinched, refit the back panel and reload the film.
-
Fill ink and check
Close the cover or, as DTF Station does, hold the cover sensor with a metal object. Go to Menu > Head Maintenance > Fill Ink > Two Head. Let it run 30 seconds from when ink starts to flow, press Cancel, run two head cleanings, then print a nozzle check from Head Maintenance > Head Status.
Never let a damper or open tube drip onto the carriage board. If you see air in the line or the nozzle check is worse than before, stop and contact us.
The ink tube assembly
The tube bundle that runs to the carriage is replaced as one assembly. The job involves removing the carriage board and its cables, the base plate, internal panels and the pumps' tubing, and rewiring two terminals. If your tubes are cracked, kinked or keep showing air, text us first and we'll confirm the part and walk you through it, or arrange service.
Watch DTF Station's video: replacing the inlet filters on the Prestige R2 and R2 Pro
Embedded from the manufacturer's official channel.
Common questions
How often should I replace the inlet filters?
DTF Station's guideline is about once a year.
Should I replace the dampers at the same time?
They're on the same once-a-year schedule, so it makes sense to plan them together. See our damper guide for how to test and replace them.
The tube is too short after I cut it. What now?
Use the tube connectors and extensions supplied with the printer. A tube that is stretched or only part-way onto the filter will pull air.
Do I need to replace the ink tubes every year too?
DTF Station doesn't set a yearly interval for tubes. Replace the tube assembly if tubes are cracked, kinked, leaking or keep showing air even with good filters and dampers. Talk to us first, because it is a big job.
- DTF Station: Prestige R2 Pro, how to replace inlet filters
- DTF Station: Prestige R2, how to replace inlet filters
- DTF Station: Prestige R2, how to replace the ink tube assembly
- DTF Station technical documentation
- AA and DTF Station support requests about R2 ink filters and ink lines, 2024 to 2026










































































