Support
Machine type
Brand
DTF Station Prestige R2 (original)

Prestige R2 Pro and R2 weak, missing or patchy white ink: how to fix it

✓ Reviewed by Jason KimUpdated 2 min readFits: Prestige R2 Pro · Prestige R2 · NeoStampa
Short answer

Start with the white head's nozzle check. If the white rows are broken, it's an ink-flow problem: settled white ink, a clog or a bad damper. If the nozzle check is clean but the white looks thin, peeks out past the edges, or disappears from fine details, the fix is in NeoStampa's white intensity and choke settings. Hot, dry rooms and fans blowing on the printer make white worse.

Match your symptom

What you see Most likely cause Go to
White rows broken or missing on the nozzle check Settled ink, clog or air in the white line Steps 1 to 3
One white channel never comes back Bad white damper Step 3
Nozzle check fine, white thin or see-through White intensity too low, or white not circulating Steps 2 and 4
A white outline around the design Choke too low Step 5
Thin lines and small text have no white under them Choke too high or low-resolution artwork Step 6
White good at first, fades after a few prints Airflow, heat, or head strike residue Step 7

Step by step

  1. Check the white head on its own

    Print a nozzle check (Menu > Head Maintenance > Head Status) on film and hold it against something dark so the white rows show. The white head is the right head (H2). If at least 90% of the white nozzles fire, skip to step 4.

  2. Get the white ink moving

    Shake the white ink bottle every day, as DTF Station's maintenance schedule calls for, and remove any paper cover from the cap so no paper falls into the ink. Make sure the bottle caps are tightened and then backed off a quarter turn so air can get in. Leave the printer powered on overnight so the white keeps circulating. If you see a steady stream of bubbles in the white tubes, don't adjust the circulation yourself: text us a video.

  3. Clear the white head

    Run Menu > Head Maintenance > Fill Ink > Right Head for 30 seconds once ink flows into the waste bottle, then two head cleanings and another nozzle check. If white is still missing, follow our nozzle check guide (wet cap) and then our damper guide. Talk to us before you remove white dampers.

  4. Raise the white intensity in NeoStampa

    For one image: click the image, open White Effect Layer on the right, set Method to Flat, and raise Intensity (%). Click Save. For every job: click the three-dot menu at the top right, pick your profile, click the white ink icon next to the 5-color setting, choose White, and change Intensity (%). Lower it the same way if white is too heavy.

  5. White peeking out at the edges: add choke

    Choke shrinks the white layer slightly inside the color so it doesn't show at the edges. In the same white ink settings, find Choke, right-click the value to switch units to millimeters, and increase it a little at a time. Click OK and choose Yes to apply it to all images. To check before printing, use Print > Process Only, then right-click the job and open the raster preview with only black and white showing.

  6. Fine details losing their white

    Rework the artwork at a higher resolution (DTF Station suggests up to 4 times, for example 300 to 1200 DPI) and lower the choke for that job only. Put the choke back to your normal value afterward, or every other job will show white edges.

  7. Fix the room

    Keep fans, air conditioning and heaters from blowing on the printer, and aim for 70 to 75°F and 35 to 45% humidity. White suffers most in hot, dry rooms. If the head has ever touched the film, residue under the head can make white fade weeks later. See our head strike guide.

Still thin after all of this? Text us a photo or short video at (562) 609-4996 of the nozzle check, the print, and your NeoStampa white settings.

Watch DTF Station's video: adjusting white ink amount and choke in NeoStampa

Embedded from the manufacturer's official channel.

Common questions

Why does my white start strong and fade after a few prints?

White ink is heavy and dries fastest. The common causes are a fan or air vent blowing on the printer, a hot and dry room, and residue from an earlier head strike. Ask yourself whether the head ever touched the film. Then send us a nozzle check from before and right after a job.

Can I print without white, CMYK only?

Yes, for designs that don't need an underbase. In Pilot the CW print mode prints color plus white and W prints white only. Text us and we'll help you set up a color-only job in your RIP.

How much choke should I use?

Increase it in small steps until the white edge disappears. Too much choke leaves thin lines and small text without enough white under them.

The white looks fine on film but the print peels or looks hazy on the shirt. Is it the printer?

Usually not. Check the powder (even coat, excess shaken off, fresh powder), curing (at least 248°F / 120°C until the surface looks like orange peel), and pressing (320°F / 160°C for 15 seconds at medium pressure).

Does leaving the printer off hurt the white?

Yes. Leave the printer on overnight so the white ink keeps circulating and the head gets its automatic cleanings. Just turn off the heater and LED.

Did this fix it?