Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prisma Dual heat press setup: uncrating, air, foot pedal, laser alignment and first press
Roll the Prisma Dual off its crate base, level and lock the four feet, then connect the air line, foot pedal and power. Turn on the press and compressor, open the ball valve and push the blue slide valve toward the gauge until pressure builds, then set 40 to 77 psi on the screen. Line up the laser on the positioning pad and test the foot pedal and two-hand PRESS buttons before your first press.
Plan on about an hour and some help: the press weighs about 456 lb and arrives in a wooden crate. You need an adjustable wrench, gloves, a utility knife, a power drill and a 2x4 beam to build a ramp.
Get it off the crate
-
Open the crate
Remove the L brackets, then the top panel and the side panels. Keep one panel for the ramp.
-
Free the base
Remove the 3 screws on each bracket that hold the machine to the crate base.
-
Raise the leveling feet
Turn each foot clockwise with the adjustable wrench until the machine rests on its casters and rolls.
-
Roll it down
Build a ramp from the removed panel and the 2x4 and roll the press down slowly and under control.
-
Level and lock it
In its final spot, adjust all four leveling feet so the machine is stable and level, and lock them.
What's in the five boxes
- #1 Air compressor
- #2 Foot pedal assembly and cables
- #3 Platen. Slide it on until it is fully seated, then push the locking lever
- #4 Laser guide pads
- #5 Teflon cover (optional)
Connect air, pedal and power
-
Air line
Pull back the locking ring on the air tube, push the tube in until it clicks, and connect it to the air port on the machine.
-
Foot pedal
Slide the strain-relief collar on and rotate it clockwise. Plug the pedal cable into its port on the machine and tighten the locking ring.
-
Power
Plug the main power cable into a grounded outlet. Put a waste bin underneath the press.
-
Laser
Peel the protective plastic off the laser guide.
Bring up the air
-
Start the compressor
Plug it in, rotate the red knob toward the air line, then pull the red knob up to switch it on. Watch the compressor gauge rise.
-
Power on the press
Switch on the Prisma Dual and wait for the control screen.
-
Let air into the press
Open the ball valve, then push the blue manual slide valve toward the pressure gauge until pressure builds.
-
Set the pressure
Tap the Pressure field on the main screen and set a value between 40 and 77 psi.
Align the laser
Point the flexible laser tube upward so the swing arm can't hit it, and tilt the laser head downward so the beam can never shine into anyone's eyes. Rotate the head to focus the lines and set their thickness. Then line up the two outer lines with the vertical centerline of the positioning pad, and the two inner lines with the horizontal centerline.
Test before your first transfer
-
Foot pedal
Press the pedal. The heat platen should swing to the opposite station.
-
Two-hand press
Press both PRESS buttons at the same time. The platen should come down and press.
-
First press
Tap Temperature, enter the value your transfer maker gives, and tap Back. Tap the Time icon or SET, choose Single press and set the time. Stay in Manual mode for your first few shirts. For DTF starting points, see DTF heat press settings.
Keep hands and body clear of the swing arm and platen while the press is running. If the status bar shows Emergency On, the RELEASE button has been pressed and the cycle has stopped. If the press won't build pressure or swing, Text us a photo or short video at (562) 609-4996.
Watch DTF Station's Prisma Dual unboxing and setup
Embedded from the manufacturer's official channel.
Common questions
What air pressure should the Prisma Dual run at?
DTF Station recommends 40 to 77 psi. You set it in the Pressure field on the main screen.
Is the air compressor included?
Yes. It ships in accessory box #1 with the press, along with the foot pedal, platen, laser guide pads and an optional Teflon cover.
The platen won't come down when I press one button. Is it broken?
No. The press only lowers when both PRESS buttons are pushed at the same time. This two-hand start is a safety feature.
Do I need 220 V?
No. The Prisma Dual comes in a 110 V version (16.64 A) and a 220 V version (8.32 A). Use a grounded outlet and keep other high-power equipment off that circuit.
Where do the power cord, pedal and air hose live?
They are stored in the side storage compartment of the machine.
- Prisma Dual operation manual
- Prisma Dual product manual
- Prisma Dual product specifications
- DTF Station technical documentation











































































