Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prisma Sentry setup: power, temperature, time, pressure knob and safety
Plug the Sentry into a grounded outlet on a full 20 amp circuit and switch it on at the side. Press Mode Select once and use plus and minus to set temperature, then press Mode Select again to set time. Turn the center knob clockwise for more pressure, close and lock the handle once it's at temperature, and open the press when the timer ends.
The Sentry needs no assembly beyond unpacking it onto a solid bench. Everything you set lives on the small control panel above the handle: three lights (temperature, set, time), a display and three buttons. The middle button is Mode Select, the left one is minus and the right one is plus.
Connect the power
- Plug into a properly grounded outlet on a full 20 amp circuit at 120 V.
- Don't use a circuit under 15 amps, or one with another heat press or other high-demand equipment on it. That causes erratic controller behavior, wrong readings, slow heat-up and breaker trips.
- Avoid extension cords. If you need one, keep it short, no lighter than 12 gauge and rated for 20 amps, and route it so nobody can trip on it.
Switch on and set it
-
Switch on
Turn on the power switch on the side of the column, just above the power inlet.
-
Set the temperature
Press Mode Select once. The temperature and set lights come on. Press plus to raise or minus to lower the target. The range goes up to 430°F (221°C).
-
Set the time
Press Mode Select again. The time and set lights come on. Use plus and minus to set 0 to 999 seconds.
-
Let it heat
Keep the press open while it heats. Allow about 20 minutes to reach 350°F.
Set the pressure
The pressure knob is in the center, above the heat platen. Turn it clockwise to increase pressure and counterclockwise to decrease it. There's no pressure readout, so adjust with the garment in place and check results. A thick hoodie needs the knob backed off compared with a thin tee.
Press
-
Load and close
Once the press is at temperature, position the garment and transfer, then lower the handle and lock it. The timer starts on its own.
-
Open when the timer ends
When the countdown finishes, lift the handle to open the press. The timer resets for the next press.
Safety
- Burns happen from the heat platen and the metal parts around it. Keep hands clear and don't leave the press switched on and unattended.
- Keep children away from the press while it's in use.
- Unplug by the plug, never the cord. Keep the cord off hot surfaces.
- Let the press cool completely before you store or cover it. Never put it in water.
- Don't use it with a damaged cord or after it has been dropped. Don't open it up to repair it yourself: contact us.
Settings by transfer type are in the heat press time and temperature chart. To switch °F or °C or correct the temperature, see Prisma Swing and Sentry calibration.
Common questions
How long does it take to heat up?
About 20 minutes to reach 350°F (180°C).
Which way do I turn the pressure knob?
Clockwise increases pressure, counterclockwise decreases it. Allow for the thickness of your garment.
Does the Sentry open by itself?
No. It is a manual-open clamshell. When the timer finishes, lift the handle to open it.
Can I run it on the same circuit as my printer or another press?
No. Use its own 20 amp circuit and don't run other high-draw equipment on it, or the breaker can trip and the display can read wrong.
How do I switch to °F?
It's in the locked second menu. See our calibration and °F/°C guide.
- Prisma Sentry operation manual (AA)
- Prisma Sentry product specifications
- AA support requests about Prisma heat press setup, 2024 to 2026











































































